| Miniproposals | ||||||||||
|
| Operators | |
| Session leader(s): | Steve Wolfe |
| Physics operator(s): | Bill Rowan |
| Engineering operator(s): | Gary Dekow,Frank Silva |
| Engineering Operator Run Comment |
| Machine Plasma Conditioning |
| Session Leader Plans |
| Physics Operators Plans |
| Session Leader Summaries |
| Entered: Jul 7 2004 03:49:22:773PM |
| Author: To Be Determined |
| Sesion Leader Summary for Wed. 4/19/2000 SL: wolfe PO: Rowan EO: Silva/Dekow Goals: Continue conditioning Run some upper nulls to condition the top of the machine, and do a little discharge development for future runs Run some "ohmic H-mode" tf programs, to see what happens (as a gauge of current machine condition) RF#1 may try to pulse between shots. Start from a re-load of 1000418016. For future reference, the upper nulls are in segment #3, and the ohmic H-modes are in segment #4. First two shots ran ok, with injections. A small gain tweak on clearin integral gain may or may not have improved the early thrash. First try at upper null was shot 3, which failed. The first successful upper null was shot 8. Additional tuning shots to get rid of several vertical thrashes and improve the rapdown continued through shot #17. Most of these were decent upper null plasmas with Mo injections, and varying amounts of thrashing, but making it into rampdown. The recycling was quite low, in that the 5e19 shots were still requiring gas puffing through the shot. Shot #17 was a Pitcher-puff, with density feedback off and no second segment gas puff except for a 50msec pg3 puff at 1sec. nl4 got to 2e19 before the puff, went up to 4e19, and noticably decayed in 300msec. Shot 18 was a lower null, 1MA, 1e20 shot which ran to completion with only a few Mo injections. This was actually run by accident, but was a useful check on machine condition. Note that the segment 4 title claims this is an ohmic h-mode, but it isn't. Shots 19-21 were attempts at ohmic h-mode. #19 disrupted at 0.6sec. After some minor shape adjustments, #20 ran to completion, but did not go into h-mode. The qpsi only got down to 2.9. For shot #21 we lowered the tf minimum from -82ka to -74ka; we got an h-mode at ~0.9sec, but the plasma died of radiation/vertical problems at 1.05sec. The h-alpha and bolo looked like the h-mode was ELM-free. All in all, a pretty successful run. The upper null development is essentially complete, although it would be good to fix the vertical position thrash in the first 100msec after segment switch. Note that seg1 zcur programs the position to start moving before t=0.1sec, so we flipped seg1 zcur as well as seg3. It may be better to run the upper nulls with zcur=0, although we only dropped it as far as +0.01 today. It looked to me as if the number of injections in upper null was decreasing as the day went on, and certainly we weren't seeing big gas influx. On the other hand, H/D was still high, not getting below 0.2 even at 1.e20 in the upper null discharges. Considering the small number of shots, the h-mode series was pretty successful as well. This was undertaken mainly as an indicator of wall condition and cleanliness, and the tentative conclusion is "Not bad, but not quite as good as 990831" which of couse was boronized. Startup was 100% today: 21/21. The only hardware problem encountered which impacted the run was two crashes of SPANNA, the Physics Operator's workstation. The RF group reports a problem with transmitter #1, which prevented them from doing vacuum conditioning between shots. |
| Physics Operator Summaries |
| Entered: Jul 7 2004 04:37:10:317PM |
| Author: To Be Determined |
| Physop summary for 1000419 Run Plan for Wednesday, April 19, 2000 Plasma run will begin at 9:00 and end by 17:00 Machine Conditioning is primary goal of run SL: Wolfe PO: Rowan EO: Silva, Dekow Engineering Setup: ------------------ ECDC. Overnight and turn off 2 hours before the run. Power system setup as on 1000418003 Fizzle detector should be on from t=0.080 to 1.7 s Gas setup - fill B-top with 6 psi of D2 Hybrid enabled fill B-side lower with 1 psi of Ar Hybrid DISABLED leave B-side upper as is Hybrid DISABLED fill C-side with 30 psi of D2 Hybrid enabled leave J-bottom as is Hybrid DISABLED The following gate valves should be enabled, assuming no vacuum problems: VUV and ECE ---------------------------------------------------------------------------- Objectives: . run ohmic H-mode. Ref. 990831015 . run upper null for conditioning . possible gap scan . continue machine conditioning . bring up RF as possible . bring up DNB as possible Run summary SL developed a diverted upper null discharge. After attaining a full length shot, worked on the ramp down to delay disruption. There is one shot (017) in this group in which the gas feed was turned off so that the density decay could be measured. This is a continuation of the wall loading experiment that was begun yesterday. SL Wolfe became bored and suggested attempting an Ohmic H Mode. The basic shot was reloaded from 990831015. The first attempt at this reload failed because the wrong segment was loaded. With the correct segment and with update of the predictors and following a TF modification to lower the q, an H-mode was obtained on the last shot of the day (021). Details of development are contained in the SL summary. Spanna crashed twice in the course of the run. Details of the run Started PCS. Loaded shot 1000418016 as the starting point. This is a shot with nl04 8e19 and and is lower than the highest density achieved on 4/18. Did coldstart and completed at 19-APR-2000 08:15:59.80 SHOT 001: Good shot. Numerous injections. Rice says that these injections are Mo Shot 002: Good shot. Numerous injections. Note gain change in CLEARIN for this shot Shot 003: Upper null attempt. Disruption at 0.2 s Inverted ZCUR for the next shot Shot 004: Disruption before 0.2 s again. Inverted ZCUR in segment 1 for the next shot. For this shot, ZCUR was inverted only in Segment 03. Shot 005: Disruption before 0.2 s again. Spanna crashed before this shot. Note changes on SL log Shot 006: Disruption at 0.45 s For the next shot, changed the integral gain on CLEARIN in segment 3 and moved the gas puff earlier in segment 1 by 0.5 ms to help with runaways Shot 007: Disruption before 0.5 s Shot 008: Reduced nl04 demand to 5E19 m-2 and made the rise slightly slower. Note change in CLEARIN Disruption at 1.8 s. Injections continue. Shot 009: Moved RCUR in by 3 mm. Moved RXL to -0.01. Moved CLEARIN to -0.015 after 0.4 s Moved RXU to -0.03. Moved ZXU down by approx 3 mm in the ramp down. Moved ZXU to 0 at early time. Disruption at 1.7 s, during rampdown Shot 010: Numerous changes. See SL log for list. Shot ended at 1.9 s. Numerous injections Shot 011. Changes in ZXL, ZXU, ZCUR. See SL log. Full length shot. Injections. Shot 012: Changes in RCUR, IP proportional gain, ZCUR, ZXL, ZXU. See SL log. Full length shot. Injections continue. Shot 013: See SL log for changes. Full length shot. Injections continue. CLEARIN is not changed as indicated due to error by PO Shot 014: Corrected error in CLEARIN. Ramp is as intended: from -0.015 at 1.5s to -0.05 at 2 s. Full length shot. Injections continue. Shot 015. Increased nel04 demand to 8e+19m-2. Increased rampdown rate of CLEARIN. Shot 016. Plasma Shot 017. SPANNA crashed before this shot. Turned off density feedback 50 ms gas puff at 1 s Shot 18: Reloaded shot 990831015 segment 2 and changed the predictors This is an error. It should have been segment 3 Shot 19: Reloaded shot 990831015 segment 3 and changed the predictors. This should be an Ohmic H-mode. Disrupted at 0.6 s. Shot 20: Changes to CLEARIN and ZXL. See SL log. Full length shot. No H-mode Shot 21: Small reduction in TF at the minimum. Flipped ZCUR in segment 1. Shot ended at 1.05 s. H-mode. Score Card. Plasmas 14 Disruptions 7 (1 was an H-mode) Fizzles 0 ---------- Total 21 |
| Session Leader Comments | |||
| Apr 19 2000 08:28:43:810AM | Steve Wolfe | Run plan for Wed. April 19, 2000 SL: wolfe PO: Rowan EO: Silva/Dekow Goals: Continue conditioning Run some upper nulls to condition the top of the machine, and do a little discharge development for future runs Run some "ohmic H-mode" tf programs, to see what happens (as a gauge of current machine condition) RF#1 may try to pulse D antenna between shots. | |
| Apr 19 2000 09:15:18:577AM | 1000419001 | Steve Wolfe | shot#1: good lower null plasma, a bit of a thrash near crossover, with injections. next shot, try stepping up the clearin integral gain (.37,.50sec) |
| Apr 19 2000 09:31:35:607AM | 1000419002 | Steve Wolfe | shot#2:try stepping up the clearin integral gain (.37,.50sec) Still lots of injections, maybe more; looks like less of a thrash in vertical position around crossover though. Next shot: try for upper null. |
| Apr 19 2000 09:49:35:797AM | 1000419003 | Steve Wolfe | shot#3: try for upper null. dies at 0.18sec. We probably did something wrong forgot to flip zcur. Is that all? We'll see. |
| Apr 19 2000 10:19:18:107AM | 1000419004 | Steve Wolfe | shot#4: try again for upper null. Still only makes it to .21sec. Make another zcur shift in seg 1 to avoid jump at 0.1sec. |
| Apr 19 2000 10:46:18:797AM | 1000419005 | Steve Wolfe | shot#5: Make another zcur shift in seg 1 to avoid jump at 0.1sec. same thing. EF2's and efc's are going crazy at and just after seg switch Next shot: Set RXL and ZXL to zero across the whole shot; Reduce initial CLEARIN Pgain from 4.95 to 2.0 Spanna is rebooting, so I make the changes |
| Apr 19 2000 11:23:42:297AM | 1000419006 | Steve Wolfe | shot#6: Set RXL and ZXL to zero across the whole shot; Reduce initial CLEARIN Pgain from 4.95 to 2.0 A little longer, 0.44sec; got to upper null ok, rather high elongation. EF2l and EFC still having a problem early, but they make it through. get a brick near crossover. Next shot, tweak clearin gain and ramp, add some early gas in seg1 for runaways. |
| Apr 19 2000 11:44:35:093AM | 1000419007 | Steve Wolfe | shot#7: tweak clearin gain and ramp, add some early gas in seg1 for runaways. plasma to ~.5sec, could be a brick, gaps maybe a little large. Still some runaways, but better. Next shot: reduce density to 5e19, reduce gap from "-.01" to "-.015" |
| Apr 19 2000 12:36:02:047PM | 1000419008 | Steve Wolfe | shot#8: reduce density to 5e19, reduce gap from "-.01" to "-.015" plasma full length. lots of injections. It goes on the gusset at the end and during rampdown. Ian comes in and disrupts. He thinks we should unchange the segment 1 vertical motion, which doesn't show up on his predictor. I prefer to wait on that until we take care of the later problems. Next shot: rcur in by 3mm, clrearin reduced later in shot to -.015, move RXU,ZXU in and down in rampdown to fix putting strike on gusset in rapdown, move rxl in by -.01, move zxu up to zero in early stage to try to help early thrash. |
| Apr 19 2000 01:16:11:577PM | 1000419009 | Steve Wolfe | shot#9: rcur in by 3mm, clrearin reduced later in shot to -.015, move RXU,ZXU in and down in rampdown to fix putting strike on gusset in rapdown, move rxl in by -.01, move zxu up to zero in early stage to try to help early thrash. plasma to 1.7, has a bad vertical thrash in rampdown. The thrash at 0.2 is still there. Next shot: drop zcur3 pgain from 8->6 between .1 and .23; extend zcur3 p gain from 1.85 to 2sec ef4 from 3000 to 2000 ef2byef4 from -2000 to -2500 zxl from -.05 to -.04 |
| Apr 19 2000 01:34:04:450PM | 1000419010 | Steve Wolfe | shot#10: drop zcur3 pgain from 8->6 between .1 and .23; extend zcur3 p gain from 1.85 to 2sec ef4 from 3000 to 2000 ef2byef4 from -2000 to -2500 zxl from -.05 to -.04 plasma full length, got rid of thrash in rampdown. still kisses the gusset from 1.7 to 1.8sec next shot: move zxu further down in rampdown set zxl from -4cm to -3cm for flattop drop zcur to 0.015 through flattop |
| Apr 19 2000 01:58:40:797PM | 1000419011 | Steve Wolfe | shot#11:move zxu further down in rampdown set zxl from -4cm to -3cm for flattop drop zcur to 0.015 through flattop shorter, got the rampdown thrash back. ef2u zeros again. next shot: undo the zxu rampdown change, up another cm on zxl, ramp zcur down to zero from 1.5-1.9sec move start of rcur ramp from .4 to .35sc delay IP gain jum p from .41 to .50 |
| Apr 19 2000 02:13:07:793PM | 1000419012 | Steve Wolfe | shot#12: undo the zxu rampdown change, up another cm on zxl, ramp zcur down to zero from 1.5-1.9sec move start of rcur ramp from .4 to .35sc delay IP gain jum p from .41 to .50 full length plasma, no thrash in rampdown, less of a thrash .4-.5 still lots of small injections. on the gusset at 1.64 sec in rampdown. Next shot: try limiting it in rampdown- rcur and clearin ramps starting at 1.5 sec drop zcur from .015 to .01 for whole flattop |
| Apr 19 2000 02:39:13:717PM | 1000419013 | Steve Wolfe | shot#13: try limiting it in rampdown- rcur and clearin ramps starting at 1.5 sec drop zcur from .015 to .01 for whole flattop; this should increase elongation a bit, and gets rid of most of the segment 2 zcur motion. NOte that the other possibility is to turn on strkpsi late in the shot to keep the strikepoint off the gusset. Also, the changes around .4 may need to be changed again for higher density, which will affect the crossover time. plasma to 1.9 sec, but has a rampdown thrash at ~1.68 still multiple injections. 0.1 to 0.2sec thrash still there, maybe worse? no supplies rail this time. still touching the gusset in rrampdown -- CLEARIN change didn't happen. Next shot: fix clearin in rampdown |
| Apr 19 2000 02:53:44:357PM | 1000419014 | Steve Wolfe | shot#14:fix clearin in rampdown plasma to 1.9sec; still takes a while to limit. next shot: raise the density from .5 to .8e20 also ramp clearin in faster in rampdown. |
| Apr 19 2000 03:14:56:920PM | 1000419015 | Steve Wolfe | shot#15: raise the density from .5 to .8e20 also ramp clearin in faster in rampdown. plasma to 1.79sec, got programmed density ef1u and ef2u rail at end of shot. fewer injections. next shot: raise nl4 to 1.0, tweak ef2 & ef4 currents in rampdown. |
| Apr 19 2000 03:32:53:403PM | 1000419016 | Steve Wolfe | shot#16: raise nl4 to 1.0, tweak ef2 & ef4 currents in rampdown. plasma to 1.7 sec, big possibly non-Mo injection at 1.1sec next shot: do a pitcher-puff with the upper null to evaluate effective recycling - turn off nl4 feedback, put a single 50 msec x 150V pulse on pg3 at 1 sec. |
| Apr 19 2000 03:51:41:483PM | 1000419017 | Steve Wolfe | shot#17: do a pitcher-puff with the upper null to evaluate effective recycling - turn OFF nl4 feedback for the whole of seg3, put a single 50 msec x 150V pulse on pg3 at 1 sec. SPANNA has crashed again! plasma to 1.92sec but had a big thrash in rampdown again. got down to 2e19 before the puff, and up to 4e19 after the puff; decays to 3.1e19 at 1.32sec (next injection). OK, that will do it for the upper null development and cleanup. There is still a bad thrash between 0.1 and 0.2 sec, but it survives it. Next shot, try for ohmic h-mode, based on 990831015 with recalculated predictors. |
| Apr 19 2000 04:09:28:763PM | 1000419018 | Steve Wolfe | shot#18: try for ohmic h-mode, based on 990831015 with recalculated predictors. OOPs - got the wrong segment. This is a 1MA normal shot. Already in INIT, let it go. Result: plasma to 1.77 sec, at 1MA, 1.1e20. OH well, it ran anyway. Next shot: load seg 3 from 990831015. This time, check it before loading. |
| Apr 19 2000 04:36:05:560PM | 1000419019 | Steve Wolfe | shot#19: load seg 3 from 990831015. This time, check it before loading. add a back porch on the tf for JHI, and enable 25msec of Ar for JR. disrupted at 0.6sec. Probably a brick, but n/nc is a little high and the strike points are on the floor. next shot: drop clearin by ~2mm, and raise xpt by 5mm |
| Apr 19 2000 04:50:45:997PM | 1000419020 | Steve Wolfe | shot#20: drop clearin by ~2mm, and raise xpt by 5mm plasma to 1.8sec, no h-mode. Note that we forgot to flip the zcur in seg1 back from the upper null setting. do that for next shot. Also, reduce tf to -74kA from -82 to reduce q below 2.9 |
| Apr 19 2000 05:01:49:137PM | 1000419021 | Steve Wolfe | shot#21: fix seg1 zcur flip. Also, reduce tf to -74kA from -82 to reduce q below 2.9 disrupted at 1.05sec, injested something at 0.9s it went into h-mode, then radiated itself away. density and wmhd went up at 0.9, h-alpha drops, elm-free. That's all for today. No run tomorrow. |
| Physics Operator Comments | |||
| Apr 19 2000 10:10:33:043AM | Ian Hutchinson | Run Plan for Wednesday, April 19, 2000 Plasma run will begin at 9:00 and end by 17:00 Machine Conditioning is primary goal of run SL: Wolfe PO: Rowan EO: Silva Engineering Setup: ------------------ ECDC. Overnight and turn off 2 hours before the run. Power system setup as on 1000418001 Fizzle detector should be on from t=0.080 to 1.7 s Gas setup - fill B-top with 6 psi of D2 Hybrid enabled fill B-side lower with 1 psi of Ar Hybrid DISABLED leave B-side upper as is Hybrid DISABLED fill C-side with 30 psi of D2 Hybrid enabled leave J-bottom as is Hybrid DISABLED The following gate valves should be enabled, assuming no vacuum problems: VUV and ECE ---------------------------------------------------------------------------- Objectives: . run ohmic H-mode. Ref. 990831015 . run upper null for conditioning . possible gap scan . continue machine conditioning . bring up RF as possible . bring up DNB as possible Started PCS. Loaded shot 1000418016 as the starting point. This is a shot with nl04 8e19 and and is lower than the highest density achieved on 4/18. Did coldstart and completed at 19-APR-2000 08:15:59.80 | |
| Apr 19 2000 09:15:24:233AM | 1000419001 | Bill Rowan | SHOT 001: Good shot. Numerous injections. Rice says that these injections are Mo Note gain change in CLEARIN |
| Apr 19 2000 09:31:24:780AM | 1000419002 | Bill Rowan | Shot 002: Good shot. Numerous injections. Note gain change in CLEARIN for this shot |
| Apr 19 2000 09:51:56:763AM | 1000419003 | Bill Rowan | Shot 003: Upper null attempt. Disruption at 0.2 s Inverted ZCUR for the next shot |
| Apr 19 2000 10:19:01:090AM | 1000419004 | Bill Rowan | Shot 004: Disruption before 0.2 s again. Inverted ZCUR in segment 1 for the next shot. For this shot, ZCUR was inverted only in Segment 03. |
| Apr 19 2000 10:49:34:217AM | 1000419005 | Bill Rowan | Shot 005: Disruption before 0.2 s again. Spanna crashed before this shot. Note changes on SL log |
| Apr 19 2000 11:23:37:013AM | 1000419005 | Bill Rowan | Shot 006: Disruption at 0.45 s For the next shot, changed the integral gain on CLEARIN in segment 3 and moved the gas puff earlier in segment 1 by 0.5 ms to help with runaways |
| Apr 19 2000 11:45:51:500AM | 1000419005 | Bill Rowan | Shot 008: Reduced nl04 demand to 5E19 m-2 and made the rise slightly slower Note change in CLEARIN |
| Apr 19 2000 12:35:34:593PM | 1000419008 | Bill Rowan | Shot 008: Reduced nl04 demand to 5E19 m-2 and made the rise slightly slower Note change in CLEARIN Disruption at 1.8 s. Injections continue. |
| Apr 19 2000 12:40:04:093PM | 1000419009 | Bill Rowan | Shot 009: Moved RCUR in by 3 mm. Moved RXL to -0.01. Moved CLEARIN to -0.015 after 0.4 s Moved RXU to -0.03. Moved ZXU down by approx 3 mm in the ramp down. Moved ZXU to 0 at early time. Disruption at 1.7 s, during rampdown |
| Apr 19 2000 01:35:07:653PM | 1000419010 | Bill Rowan | Shot 010: Numerous changes. See SL log for list. Shot ended at 1.9 s. Numerous injections |
| Apr 19 2000 01:59:51:543PM | 1000419011 | Bill Rowan | Shot 011. Changes in ZXL, ZXU, ZCUR. See SL log. Full length shot. Injections. |
| Apr 19 2000 02:15:01:217PM | 1000419012 | Bill Rowan | Shot 012: Changes in RCUR, IP proportional gain, ZCUR, ZXL, ZXU. See SL log. Full length shot. Injections continue. |
| Apr 19 2000 02:40:34:013PM | 1000419012 | Bill Rowan | Shot 013: See SL log for changes. Full length shot. Injections continue. CLEARIN is not changed as indicated in SL log due to error by PO |
| Apr 19 2000 03:08:59:810PM | 1000419014 | Bill Rowan | Shot 014: Corrected error in CLEARIN. Ramp is as intended: from -0.015 at 1.5s to -0.05 at 2 s Full length shot. Injections continue. |
| Apr 19 2000 03:09:25:733PM | 1000419015 | Bill Rowan | Shot 015. Increased nel04 demand to 8e+19m-2. Increased rampdown rate of CLEARIN. |
| Apr 19 2000 03:48:35:000PM | 1000419017 | Bill Rowan | Shot 017. SPANNA crashed before this shot. Turned off density feedback 50 ms gas puff at 1 s Full length shot |
| Apr 19 2000 04:18:10:810PM | 1000419018 | Bill Rowan | Shot 18: Reloaded shot 990831015 segment 2 and changed the predictors This is an error. It should have been segment 3 |
| Apr 19 2000 04:29:52:233PM | 1000419019 | Bill Rowan | Shot 19: Reloaded shot 990831015 segment 3 and changed the predictors. This should be an Ohmic H-mode. Disrupted at 0.6 s. |
| Apr 19 2000 04:51:37:623PM | 1000419019 | Bill Rowan | Shot 20: Changes to CLEARIN and ZXL. See SL log. Full length shot. No H-mode |
| Apr 19 2000 05:02:39:013PM | 1000419021 | Bill Rowan | Shot 21: Small reduction in TF at the minimum. Flipped ZCUR in segment 1. Shot ended at 1.05 s H-mode. |
| Apr 19 2000 08:26:12:530AM | 1000419025 | Bill Rowan | Run Plan for Wednesday, April 19, 2000 Plasma run will begin at 9:00 and end by 17:00 Machine Conditioning is primary goal of run SL: Wolfe PO: Rowan EO: Silva Engineering Setup: ------------------ ECDC. Overnight and turn off 2 hours before the run. Power system setup as on 1000418001 Fizzle detector should be on from t=0.080 to 1.7 s Gas setup - fill B-top with 6 psi of D2 Hybrid enabled fill B-side lower with 1 psi of Ar Hybrid DISABLED leave B-side upper as is Hybrid DISABLED fill C-side with 30 psi of D2 Hybrid enabled leave J-bottom as is Hybrid DISABLED The following gate valves should be enabled, assuming no vacuum problems: VUV and ECE ---------------------------------------------------------------------------- Objectives: . run ohmic H-mode. Ref. 990831015 . run upper null for conditioning . possible gap scan . continue machine conditioning . bring up RF as possible . bring up DNB as possible Started PCS. Loaded shot 1000418016 as the starting point. This is a shot with nl04 8e19 and and is lower than the highest density achieved on 4/18. Did coldstart and completed at 19-APR-2000 08:15:59.80 |
| Engineering Operator Comments | ||||
| Shot | Time | Type | Status | Comment |
| 1 | 08:56:46:310AM | Plasma | Ok | No Faults/Plasma |
| 2 | 09:17:40:967AM | Plasma | Ok | No Faults/Plasma |
| 3 | 09:35:46:717AM | Plasma | Ok | No Faults/Disrupt |
| 4 | 09:53:09:060AM | Plasma | Ok | No Faults/Disrupt |
| 5 | 10:19:54:043AM | Plasma | Ok | No Faults/disrupt |
| 6 | 10:48:11:170AM | Plasma | Ok | No Faults/disrupt |
| 7 | 11:30:16:640AM | Plasma | Ok | No Faults/PLasma |
| 8 | 11:55:09:560AM | Plasma | Ok | No Faults/Plasma |
| 9 | 12:36:39:467PM | Plasma | Ok | No Faults/Plasma |
| 10 | 01:18:10:843PM | Plasma | Ok | No Faults/Plasma |
| 11 | 01:40:27:060PM | Plasma | Ok | No Faults/Plasma |
| 12 | 02:00:56:090PM | Plasma | Ok | No Faults/Plasma |
| 13 | 02:25:15:387PM | Plasma | Ok | |
| 14 | 02:43:23:013PM | Plasma | Ok | |
| 15 | 03:03:45:530PM | Plasma | Ok | |
| 16 | 03:24:11:140PM | Plasma | Ok | |
| 17 | 03:43:20:780PM | Plasma | Ok | |
| 18 | 04:03:28:623PM | Plasma | Ok | |
| 19 | 04:22:21:623PM | Plasma | Ok | |
| 20 | 04:39:24:500PM | Plasma | Ok | |
| 21 | 04:55:28:873PM | Plasma | Ok | |