Alcator C-Mod Run 1020723 Information

Back to runs

Miniproposals
Miniproposal:
Date Filed:
Title:
First Author:
Session Leader:Steve Wukitch (shots 1-16)

Operators
Session leader(s):Steve Wukitch
Physics operator(s):Ron Parker
Engineering operator(s):Bill Cochran,Gary Dekow

Engineering Operator Run Comment
RF Conditioning; SL:Wukitch; PO:Parker; EO:Dekow/Cochran

Session Leader Plans

Physics Operators Plans

Session Leader Summaries
Entered: Jul 7 2004 03:49:29:460PM
Author: To Be Determined
Engineering setup for Tuesday 23 July 2002

Session leader: S. Wukitch
Physics operator: R. Parker

ECDC in D2 at 2e-4 Torr from 06:00-07:00.
Set up for possible ECDC in D2 between shots.
10 minutes of ECDC before first plasma.

Run begins at 10:00 and ends at 17:00.

Power systems the same as for shot 1020716015.

Gas setup:
fill B-Top with 6 psi D2 Hybrid enabled (PG4)
fill B-side lower with 1 psi Ar Hybrid enabled (PG1)
fill B-side upper with 10 psi D2 Hybrid DISABLED (PG2) (for ECDC)
fill C-side with 30 psi D2 Hybrid enabled (PG3)
leave J-Bottom as is Hybrid DISABLED (PG5)

Enable the following gate valves, assuming no vacuum problems:
ECE

-------------------------------------------------------------------------------
RF Setup: All 4 transmitters in Run On by 07:00.

Purpose:

Plasma conditioning of antennas

-------------------------------------------------------------------------------


001 plasma attempt after morning of RF vacuum conditioning

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
digital phase is set to 225deg

result: fizzle

002

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
digital phase is set to 225deg

result: plasma
D: couple of faults
E: couple of faults
J: faulted out early

action: retune D, E, and J

003

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: couple of faults
E: couple of faults
J: J3 faulted but stayed on after J4 faulted off

appears J4 counted max faults but J3 did not - This appears to be a
leftover feature of the control system. Dave Terry is looking into a
fix.

004

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma - early disruption ~0.36 sec
injection from J with no RF power

005

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma - early disruption ~0.42 sec
injection from J with no RF power

action: vacuum shot to test B-dot probe operation - test shot 780

test shot 780: probes appear to be fine.

5 minutes of ECDC before next shot.

006

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle

007

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle

008

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: improved
J: faulted out

action: repeat

notes: JV1-JV3 has false phase balance faults when D and E are running
raised power threshold to 700 mv from 600 mV

009

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle

note: J-port antenna view is now in the D-port antenna view until
further notice.

010

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: faulting
J: faulted out

action: raise power on D and E
slow the power ramp on J

011

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: faulting
J: ran longer!

action: retune D and E for H-mode
slower power ramp on J

012

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: faulting
J: ran a bit

action: inner wall limit to avoid H-mode

013

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.15 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.15 MW ramp @[1.2-1.6]sec

result: plasma
D: clean!
E: 3 faults
J: ran a bit

action: repeat

014

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.15 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.15 MW ramp @[1.2-1.6]sec

result: fizzle

015

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.3 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.3 MW ramp @[1.2-1.6]sec

result: plasma - early disruption

016

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.3 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.3 MW ramp @[1.2-1.6]sec

result: fizzle

Summary:

Vacuum conditioned the antennas before the run this morning. D and
E-port were conditioned to ~39 kV and 38 kV respectively. More time
will be required to obtain the 40 kV limit. J4 conditioned easily to
34.5 kV but J3 required significant effort to condition. J3
eventually conditioned to 34 kV. The new re-try electronics was
installed and demonstrated to function in E-port. The J-port phase
feedback was also confirmed to be operating properly during plasma
discharges.

Plasma operation had some success. Discharge 013 had the cleanest RF
pulses of the campaign. From DC0 the power level was 1.3 MW but DC1
and DC2 both suggest the net power was 1.8 MW. J-port was struggling
until 012 and 013 but will need further conditioning to see
improvement. Furthermore, injections on 004, 005, and 015 appear to
eminate from the J-port antenna area. However, the RF is off at the
time of the injections. Vacuum shots after 005 indicated that the
B-dot probes are still functional.

Physics Operator Summaries
Entered: Jul 7 2004 04:37:15:397PM
Author: To Be Determined
Engineering Setup for TUESDAY, JULY 23, 2002

Continuation of RF Conditioning
SL: Wukitch
PO: Parker


ECDC from 06:00-07:00 at 2e-4 T D2.
ECDC for 10 minutes before run.

**Run Begins at 10:00 and ends at 17:00**

Power systems setup the same as for Shot 1020719002
Gas setup:

B-Top 6 psi D2 Hybrid Enabled (PG4)
B-side lower 1 psi Ar Hybrid Enabled (PG1)
B-side upper 10 psi D2 Hybrid DISABLED (PG2, for ECDC)
C-Side 30 psi D2 Hybrid Enabled (PG3)
J-Bottom leave as is, Hybrid DISABLED

Enable the following gate valves, assuming no vacuum problems:

ECE

RF Setup: All 4 transmitters in Run On by 07:00




RUN PLAN:

We'll continue RF conditioning efforts

RUN SUMMARY:

The run got underway late (~10:30) due to need for RF conditioning.
The first shot fizzled, possibly due to BZ offset being too large. This was
reduced and the next two shots went off as planned with RF.

Shots 4&5 disrupted, the cause apparently associated with some sort of arc
appearing on the J port antenna, before the RF even turned on.

The run was then delayed in order to test the integrity of the J port
antenna probes, suspected as culprits in the arcing. No problem was
found and the run then resumed.

Shots 6&7 fizzled, apparently correlated with the appearance of a
vacuum leak as indicated on the RGA (Strong appearance of 14 line, and
significant level of 40.)

Shot 8 ran, but shot 9 fizzled. The fizzles are correlated with higher
levels of CII during the current ramp (but this could also be an effect,
rather than a cause.)

The fill pressure was then reduced by ~ 10% (the gauge was not working), and
the next three shots ran as programmed, but without much power from J port.

Unfortunately the camera looking at the J port antenna was not working on
these shots, so it was not possible to tell if the arcing was still present.

Shot 13 was programmed to be limited and it ran as programmed. Shot 14
fizzled, again with a high level of CII probably the result of the first
limited shot since the break. Shot 15 then started up sluggishly, and
disrupted early (~0.35 s). The camera looking at J port showed that the
antenna again had arcing on its surface.

Finally, the last shot fizzled, again correlated with a high level of CII.

Scorecard: 7 Shots
6 Fizzles
3 Disruptions

Session Leader Comments
Jul 23 2002 11:16:00:297AM1020723001Steve Wukitch001 plasma attempt after morning of RF vacuum conditioning

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
digital phase is set to 225deg

result: fizzle
Jul 23 2002 11:16:12:533AM1020723002Steve Wukitch002

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
digital phase is set to 225deg

result: plasma
D: couple of faults
E: couple of faults
J: faulted out early

action: retune D, E, and J
Jul 23 2002 01:30:14:190PM1020723003Steve Wukitch003

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: couple of faults
E: couple of faults
J: J3 faulted but stayed on after J4 faulted off

appears J4 counted max faults but J3 did not - This appears to be a
leftover feature of the control system. Dave Terry is looking into a
fix.
Jul 23 2002 01:30:44:177PM1020723004Steve Wukitch004

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma - early disruption ~0.36 sec
injection from J with no RF power
Jul 23 2002 01:31:01:443PM1020723005Steve Wukitch005

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma - early disruption ~0.42 sec
injection from J with no RF power

action: vacuum shot to test B-dot probe operation - test shot 780

test shot 780: probes appear to be fine.

5 minutes of ECDC before next shot.
Jul 23 2002 01:31:24:317PM1020723006Steve Wukitch006

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle
Jul 23 2002 02:16:50:590PM1020723007Steve Wukitch007

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle
Jul 23 2002 02:17:13:857PM1020723008Steve Wukitch008

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: improved
J: faulted out

action: repeat
Jul 23 2002 02:25:11:620PM1020723009Steve Wukitch009

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.5 MW ramp @[0.6-1.2]sec
J3: 0.2 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.2 - 0.25 MW ramp @[1.2-1.6]sec

result: fizzle
Jul 23 2002 04:16:14:697PM1020723011Steve Wukitch011

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: faulting
J: ran longer!

action: retune D and E for H-mode
slower power ramp on J
Jul 23 2002 04:16:30:667PM1020723012Steve Wukitch012

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.25 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.25 MW ramp @[1.2-1.6]sec

result: plasma
D: still faulting
E: faulting
J: ran a bit

action: inner wall limit to avoid H-mode
Jul 23 2002 04:17:08:620PM1020723013Steve Wukitch013

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.15 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.15 MW ramp @[1.2-1.6]sec

result: plasma
D: clean!
E: 3 faults
J: ran a bit

action: repeat
Jul 23 2002 04:17:26:120PM1020723014Steve Wukitch014

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.15 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.15 MW ramp @[1.2-1.6]sec

result: fizzle
Jul 23 2002 05:03:49:347PM1020723015Steve Wukitch015

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.3 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.3 MW ramp @[1.2-1.6]sec

result: plasma - early disruption
Jul 23 2002 05:04:01:550PM1020723016Steve Wukitch016

request:lower SN Ip~0.8 MA, BT~5.4 T, nl_04~1x10^20 m^-2
D: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
E: 0.2 - 0.7 MW ramp @[0.6-1.2]sec
J3: 0.1 - 0.3 MW ramp @[1.2-1.6]sec
J4: 0.1 - 0.3 MW ramp @[1.2-1.6]sec

result: fizzle

Physics Operator Comments
Jul 23 2002 11:22:33:293AM1020723001Ron Parker
First shot delayed to allow for RF conditioning.

Cold start revealed A matrix not responding. This was due to a reboot of
Spanna without invoking ccl remcam.

The first shot loaded was 1020719002, with segment 1 taken from
1020719023, segment 1.

In the event, shot 1 fizzled possibly because the BZ offset was too negative.
Jul 23 2002 11:20:28:897AM1020723002Ron ParkerShot 2 succeeded. The only change from shot 1 was to increase EF4 from -1320
to -1310 A, since the BZ offset in shot 1 was ~ -4 mT at t=0.
Jul 23 2002 11:49:03:080AM1020723003Ron ParkerShot 3 ran well. Next shot: Repeat.
Jul 23 2002 12:22:23:180PM1020723004Ron ParkerShot 4 disrupted beginning at ~ 0.3 s for no apparent reason.

On further examination, the disruption appears to be due to a plasma interaction
with the J-port antenna before the RF turns on.

We'll try it again.
Jul 23 2002 12:23:29:650PM1020723005Ron ParkerShot 5 also disrupted, again associated with an interaction with J port
antenna.
Jul 23 2002 01:09:43:253PM1020723005Ron ParkerFollowing shot 5, which disrupted similarly to 4, although a bit later,
there was a delay to test the RF probes via cold tests of J port antenna.

The results were normal, so no obvious problem was identified. After
a five minute ECDC, operation will be resumed.


Jul 23 2002 01:27:12:407PM1020723006Ron ParkerShot 6 fizzled, probably due to choking on impurities left by the RF tests.

Next shot will be a repeat.
Jul 23 2002 01:43:50:400PM1020723007Ron ParkerShot 7 also was a fizzle. The RGA looks suspiciously like there may be a leak.

There will be a delay while the vacuum integrity is checked.
Jul 23 2002 02:23:52:977PM1020723008Ron ParkerShot 8 ran as programmed.
Jul 23 2002 02:25:11:493PM1020723009Ron ParkerShot 9 fizzled. Too much carbon in the initial burnout.

We'll lower the pressure for the next shot (~ 10 %, 2 ms)
Jul 23 2002 02:43:01:460PM1020723009Ron ParkerSlight delay before shot 10 to fix camera looking at J port.
Jul 23 2002 02:52:23:207PM1020723010Ron ParkerShot 10 ran as programmed. Vacuum at time of pulse was ~9e-7 T

Jul 23 2002 03:34:46:583PM1020723011Ron ParkerShot 11 ran as programmed.
Jul 23 2002 03:47:25:307PM1020723012Ron ParkerShot 12 ran as programmed.

Shot 13 will be programmed to run inner wall limited (with same outer gap.)
Jul 23 2002 04:13:13:490PM1020723013Ron ParkerShot 13 ran as programmed, inner wall limited.

Next shot: Repeat of 13.
Jul 23 2002 04:33:26:690PM1020723014Ron ParkerShot 14 fizzled, probably due to impurities left behind by the limited
discharge in shot 13.

Next shot: Repeat.
Jul 23 2002 04:40:12:233PM1020723015Ron ParkerShot 15 started up, barely, but disrupted at ~ 0.35 s.

Again, CII was high during the startup phase.

Next shot will be the last, a repeat of shot 15.
Jul 23 2002 05:03:27:363PM1020723016Ron ParkerShot 16 was a fizzle, consistent with high level of CII during current ramp.

Engineering Operator Comments
ShotTimeTypeStatusComment
110:38:10:973AMPlasmaOk
211:09:00:380AMPlasmaOk
311:24:58:513AMPlasmaOk
411:50:36:723AMPlasmaOk
512:18:37:003PMPlasmaOk
601:22:33:053PMPlasmaOk
701:35:41:293PMPlasmaOk
802:01:57:317PMPlasmaOk
902:16:37:433PMPlasmaOk
1002:44:39:773PMPlasmaOk
1103:06:02:260PMPlasmaOk
1203:34:14:223PMPlasmaOk
1303:53:59:647PMPlasmaOk
1404:13:27:037PMPlasmaOk
1504:33:43:580PMPlasmaOk
1604:56:49:853PMPlasmaOk