| Miniproposals | ||||||||||||
|
| Operators | |
| Session leader(s): | Martin Greenwald,M. Sampsell |
| Physics operator(s): | Jim Irby |
| Engineering operator(s): | Gary Dekow,Ed Fitzgerald |
| Engineering Operator Run Comment |
| Miniproposal 334A, QC Mode in Ohmic EDA's; PO: Irby ; EO: Dekow/ Fitz |
| Session Leader Plans |
| Physics Operators Plans |
| Session Leader Summaries |
| Entered: Jul 7 2004 03:49:33:617PM |
| Author: M. Sampsell |
| MP 334a Phys Op: Irby Session Leader: Greenwald, Sampsell Plan: We want to extend studies of the QC mode, which is implicated in the drop in particle transport seen in EDA H-modes when compared to ELM-free. We will run ohmic EDA H-modes at low power levels to allow the deep penetration of the scanning probe. The goals are to: {1.}Verify the extent and radial structure of the quasi-coherent fluctuation and its relation to density and temperature profiles using the new scanning probe head with radially offset probe tips. {2.} Look for the high frequency companions of the QC mode predicted by the BOUT code. Because the range of the scanning probe is limited by incident heat flux, we will run EDA H-modes at low powers - that is with only Ohmic heating. Following the recipe that was successful on 1000928015 (and earlier), we will begin with discharges at relatively low q and then scan B$_T$ to raise q allowing access to the EDA regime. Results: The run was not very successful. We were not able to produce and ohmic EDA - in fact we were barely able to run ohmic h-modes. The problem was a series of disruptions which occurred during the rampdown. Field errors are definitely implicated in these disruptions. The A coils were turned on for shot 24 - with no other program change, the plasma did not disrupt. The toroidal field was scanned looking for an appropriate operating point. Thus we determined the threshold for disruption with and without the A coils. Without A coils: below ~3.2-3.55 T disrupts With A coils below ~2.6-2.9 T disrupts Some interesting high-frequency broadband fluctuations were observed with the faster digitizers on the scanning probe - for example see shot 24. |
| Physics Operator Summaries |
| Entered: Jul 7 2004 04:37:18:550PM |
| Author: Jim Irby |
| Physop Summary for run 1030703, QC Mode in Ohmic EDA's The primary lesson learned today was that the A-Coils should ALWAYS be on. We spent nearly the whole day dealing with disruptions. It is clear that we can not reproduce results we had during run 1000928 without the correction coils. Bob Granetz suggested adding the coils on shot 24 which produced a full length discharge with several elm-free h-modes. On the other hand, even with the correction coils we did not get results as good as those in 2000, and the plasma still disrupted when the TF was ramped down below 3 T (as opposed to 2.7 T during the earlier run). The disruptions all seemed to be related to the H-to-L back transition. We never actually got an EDA discharge; only elm-free ones. The first three shots of the run were taken using a shot from the previous day in seg 2, with a modified TF waveform to match the earlier runs from 2000. On shot 4 we simply reloaded shot 1000928015 and dealt with all the recals required to load an older shot. This change may have improved the the discharge slightly (lasted a little longer before disruption). However, this shot was not reloaded for the the shots following the application of the A-Coils, so we don't really know how the old shot would have run. Plasmas 01,02,03,04,06,07,08,09,10,11, 12,13,14,15,16,17,18,19,20,21, 22,23,24,25,26,27,28 Fizzles 05 No duds No tests ---------------------------------------------------------------------------- 1030703xxx irby PHYSICS_OPERATOR Jul 3 2003 7:27:37:963AM . . . . . . . . . . . . . . . . . . . . Engineering setup for run 1030703, Thu, July 3, in support of Miniproposal 334A, QC Mode in Ohmic EDA's overnight ECDC in D2, stopping 1-2 hours prior to the run. Run begins at 9:00 and this portion ends at 17:00. Power system setup as on 1030702013 Gas setup fill B-top with 6 psi of D2 Hybrid enabled fill B-side lower with 1 psi of Ar Hybrid enabled fill B-side upper with 10 psi of D2 Hybrid Disabled (for ECDC) fill C-side with 30 psi of D2 Hybrid enabled The following gate valves should be enabled: ECE, VUV, DNB *** NO RF POWER WILL BE REQUIRED *** Special Requirements -------------------- All possible pedestal profile and fluctuation diagnostics Small NINJA D2 or He puff required for GPI Fluctuation diagnostics at high clock rates BES/Beam operators should check the miniprosal for special setup requirements ---------------------------------------------------------------------------- 1030703xxx irby OPS Jul 3 2003 8:32:42:066AM . . . . . . . . . . . . . . . . . . . . Tommy and Ronald have found the leak at G-Hor on one of the Thomson Scattering actuators. We will purge it with helium for this run. ---------------------------------------------------------------------------- 1030703001 irby PHYSICS_OPERATOR Jul 3 2003 9:24:50:190AM . . . . . . . . . . . . . . . . . . . . Note that the leak we have had for two days has been localized to G-HOR on one of the TS actuators. We will purge with helium for this run. Loaded 1030702013 into seg 2. Left seg 1 from 1030702040. Inner gap will have to be adjusted after first shot to match 1000927915 which is the model EDA shot Copied seg 2 of 1000928015 into seg 3 Copied/Pasted TF current from seg 3 to seg 2 Seg 3 is off Plasma for 1.12 s --- no EDA ---------------------------------------------------------------------------- 1030703002 irby PHYSICS_OPERATOR Jul 3 2003 10:01:22:340AM . . . . . . . . . . . . . . . . . . . . Loaded NL_04 programming from seg 3 (1000928015) to seg 2. Density was too high last shot. Changed CLEARIN by +.005 m --- Brian would like inner gap to be .018 m. --------------- Plasma to 1 s CLEARIN now .015 m. --- will tweak out to .018 m for next shot ---------------------------------------------------------------------------- 1030703003 irby PHYSICS_OPERATOR Jul 3 2003 10:25:32:643AM . . . . . . . . . . . . . . . . . . . . Raised density a little to better match 1000928015 Dropped current by 20 kA increased CLEARIN by another .002 m ------------------- Plasma to 1 s again next shot we will reload the old shot ---------------------------------------------------------------------------- 1030703004 irby PHYSICS_OPERATOR Jul 3 2003 10:44:26:986AM . . . . . . . . . . . . . . . . . . . . Loaded 1000928015 into seg 2. Did recals on all the lines (with Wolfe help) Plasma for 1.14 s --- a little better --- an early h-mode ---------------------------------------------------------------------------- 1030703005 irby PHYSICS_OPERATOR Jul 3 2003 11:07:24:536AM . . . . . . . . . . . . . . . . . . . . Min Bt from -2.6 to -2.7 T Decreased CLEARIN by .002 m --- better match for inner wall scanning probe Helium gas bottle purging leak at G-Hor ran out of gas Fizzle ----- either previous disruption or leak?? We are delaying the run to replace the helium bottle.... ---------------------------------------------------------------------------- 1030703006 irby PHYSICS_OPERATOR Jul 3 2003 11:33:43:250AM . . . . . . . . . . . . . . . . . . . . Helium bottle replaced --- now under better regulation No PCS changes plasma to 1.25 s --- a little better -- h-mode at 1.0 s looks like Brian has the inner gap he needs Bt was a little too negative for Martin -- about 2.8 vs 2.7 that he asked for ---------------------------------------------------------------------------- 1030703007 irby PHYSICS_OPERATOR Jul 3 2003 11:47:41:816AM . . . . . . . . . . . . . . . . . . . . Dropped TF by 10 kA Operator error --- started INIT before TF change was loaded Plasma for 1.18 s --- late/weak h-mode ---------------------------------------------------------------------------- 1030703008 irby PHYSICS_OPERATOR Jul 3 2003 12:09:46:743PM . . . . . . . . . . . . . . . . . . . . Tf no longer ramping back up after 1 s. Just rampdown and hold --- will it still disrupt? Plasma to 1.23 s --- no better than earlier shots H-mode starts at 1.1 but goes away by 1.18 s ---------------------------------------------------------------------------- 1030703009 irby PHYSICS_OPERATOR Jul 3 2003 12:28:55:520PM . . . . . . . . . . . . . . . . . . . . Dropped NL_04 request by about 10% from 6.2 to 5.6e19 / m^2 plasma for 1.25 s --- h-mode starting 1.11 s very little change in nl_04 --- pre-programmed gas? ---------------------------------------------------------------------------- 1030703010 irby PHYSICS_OPERATOR Jul 3 2003 12:37:36:270PM . . . . . . . . . . . . . . . . . . . . Eliminated preprogrammed gas on PG3 plasma for 1.23 s --- short h-mode got lower density but h-mode worse and discharge length shorter ---------------------------------------------------------------------------- 1030703011 irby PHYSICS_OPERATOR Jul 3 2003 12:57:52:706PM . . . . . . . . . . . . . . . . . . . . CLEARIN reduced by another .002 m ---- give Brian a .014 m inner gap Reduced argon from 30 ms to 6 ms plasma for 1.25 s --- weak h-mode ---------------------------------------------------------------------------- 1030703012 irby PHYSICS_OPERATOR Jul 3 2003 1:15:33:686PM . . . . . . . . . . . . . . . . . . . . Changed RXL and ZXL to move the plasma in and up about 1 cm. There was a 1 cm jerk in ZXL around the time of the disruption. Reduced CLEARIN another 2 mm for Brian. plasma for 1.29 s --- a record, but no h-mode ---------------------------------------------------------------------------- 1030703013 irby PHYSICS_OPERATOR Jul 3 2003 1:23:46:980PM . . . . . . . . . . . . . . . . . . . . Ip from -800 to -840 kA plasma 0.7 s --- try decreasing Ip next ---------------------------------------------------------------------------- 1030703014 irby PHYSICS_OPERATOR Jul 3 2003 1:40:29:226PM . . . . . . . . . . . . . . . . . . . . Ip from 840 to 760 kA plasma for 1.4 s --- longest yet, but no h-mode ---------------------------------------------------------------------------- 1030703015 irby PHYSICS_OPERATOR Jul 3 2003 2:05:47:263PM . . . . . . . . . . . . . . . . . . . . Reload 1030703009 --- longest lasting h-mode loaded 1030703014 CLEARIN into seg 2 --- keep Brian's inner gap plasma for 1.15 s ---- ---------------------------------------------------------------------------- 1030703016 irby PHYSICS_OPERATOR Jul 3 2003 2:11:30:803PM . . . . . . . . . . . . . . . . . . . . Reloaded ramp up from shot 1030703003 plasma for 1.15 s --- will reload shot from yesterday next just to get a plasma. ---------------------------------------------------------------------------- 1030703017 irby PHYSICS_OPERATOR Jul 3 2003 2:31:33:820PM . . . . . . . . . . . . . . . . . . . . Loaded shot 1030702013 into seg 2 --- still has a ramp down to 4.5 T plasma into rampdown ---- rampdown more on next shot ---------------------------------------------------------------------------- 1030703018 irby PHYSICS_OPERATOR Jul 3 2003 2:39:40:440PM . . . . . . . . . . . . . . . . . . . . TF ramped down to 95 kA (3.5 T) by 0.9 s plasma into rampdown --- some dithering past 1.2 s ---------------------------------------------------------------------------- 1030703019 irby PHYSICS_OPERATOR Jul 3 2003 3:02:12:163PM . . . . . . . . . . . . . . . . . . . . TF from 3.5 to 3.0 T nl04 from 8.5e19 to 7.0e19 / m^2 plasma for 1.37 s --- no sign of h-modes ---------------------------------------------------------------------------- 1030703020 irby PHYSICS_OPERATOR Jul 3 2003 3:14:12:853PM . . . . . . . . . . . . . . . . . . . . Rampdown to 3.0 T sooner nl04 to 8.0e19 / m^2 plasma for 1.42 s ---- h-mode next shot lower density ---------------------------------------------------------------------------- 1030703021 irby PHYSICS_OPERATOR Jul 3 2003 3:37:03:623PM . . . . . . . . . . . . . . . . . . . . nl04 from 8e19 to 6e19 / m^2 reloaded CLEARIN from shot 14 for Brian into seg 2. plasma for 1.38 s --- looks like the inner gap was very wrong?? ---------------------------------------------------------------------------- 1030703022 irby PHYSICS_OPERATOR Jul 3 2003 3:53:49:243PM . . . . . . . . . . . . . . . . . . . . reloaded shot 20 into seg 2. plasma for 1.36 s --- next shot drop the density (really) ---------------------------------------------------------------------------- 1030703023 irby PHYSICS_OPERATOR Jul 3 2003 4:08:44:233PM . . . . . . . . . . . . . . . . . . . . nl04 from 8 to 6 e19 / m^2 plasma for 1.13 s --- weak, late h-mode ---------------------------------------------------------------------------- 1030703024 irby PHYSICS_OPERATOR Jul 3 2003 4:22:11:850PM . . . . . . . . . . . . . . . . . . . . Added A-coil starting at 0.4 s ramping to 4000A at .6 s plasma into rampdown (Thank you Bob Granetz for suggesting the a-coil) ---------------------------------------------------------------------------- 1030703025 irby PHYSICS_OPERATOR Jul 3 2003 4:31:54:456PM . . . . . . . . . . . . . . . . . . . . Loaded seg 2 TF programming from 1000928015 into seg 2 plasma to 1.05 s --- rampdown to low? ---------------------------------------------------------------------------- 1030703026 irby PHYSICS_OPERATOR Jul 3 2003 4:49:00:796PM . . . . . . . . . . . . . . . . . . . . TF min from 2.7 to 3.2 T plasma into rampdown but no h-mode ---------------------------------------------------------------------------- 1030703027 irby PHYSICS_OPERATOR Jul 3 2003 5:00:44:393PM . . . . . . . . . . . . . . . . . . . . Dropped TF min to 2.9 from 3.2 T plasma into rampdown --- h-modes starting 1.18 s |
| Session Leader Comments | |||
| Jul 3 2003 06:04:43:803PM | Martin Greenwald | MP 334a Phys Op: Irby Session Leader: Greenwald, Sampsell Plan: We want to extend studies of the QC mode, which is implicated in the drop in particle transport seen in EDA H-modes when compared to ELM-free. We will run ohmic EDA H-modes at low power levels to allow the deep penetration of the scanning probe. The goals are to: {1.}Verify the extent and radial structure of the quasi-coherent fluctuation and its relation to density and temperature profiles using the new scanning probe head with radially offset probe tips. {2.} Look for the high frequency companions of the QC mode predicted by the BOUT code. Because the range of the scanning probe is limited by incident heat flux, we will run EDA H-modes at low powers - that is with only Ohmic heating. Following the recipe that was successful on 1000928015 (and earlier), we will begin with discharges at relatively low q and then scan B$_T$ to raise q allowing access to the EDA regime. | |
| Jul 3 2003 06:05:23:617PM | Martin Greenwald | Results: The run was not very successful. We were not able to produce and ohmic EDA - in fact we were barely able to run ohmic h-modes. The problem was a series of disruptions which occurred during the rampdown. Field errors are definitely implicated in these disruptions. The A coils were turned on for shot 24 - with no other program change, the plasma did not disrupt. The toroidal field was scanned looking for an appropriate operating point. Thus we determined the threshold for disruption with and without the A coils. Without A coils: below ~3.2-3.55 T disrupts With A coils below ~2.6-2.9 T disrupts Some interesting high-frequency broadband fluctuations were observed with the faster digitizers on the scanning probe - for example see shot 24. | |
| Jul 3 2003 09:37:37:413AM | 1030703001 | M. Sampsell | H-mode at 1.08. Little evidence of EDA before disruption. |
| Jul 3 2003 10:18:02:850AM | 1030703003 | M. Sampsell | For next shot we're loading shot specified in the run plan. So far we were loading a shot from yesterday that was close in many ways, but we don't know why it is disrupting. |
| Jul 3 2003 10:57:03:427AM | 1030703004 | M. Sampsell | H-modes at .75 and 1.1 s. No EDA. Disruption at 1.14s. |
| Jul 3 2003 10:57:35:960AM | 1030703005 | M. Sampsell | Fizzle. |
| Physics Operator Comments | |||
| Jul 3 2003 07:27:37:963AM | Jim Irby | Engineering setup for run 1030703, Thu, July 3, in support of Miniproposal 334A, QC Mode in Ohmic EDA's overnight ECDC in D2, stopping 1-2 hours prior to the run. Run begins at 9:00 and this portion ends at 17:00. Power system setup as on 1030702013 Gas setup fill B-top with 6 psi of D2 Hybrid enabled fill B-side lower with 1 psi of Ar Hybrid enabled fill B-side upper with 10 psi of D2 Hybrid Disabled (for ECDC) fill C-side with 30 psi of D2 Hybrid enabled The following gate valves should be enabled: ECE, VUV, DNB *** NO RF POWER WILL BE REQUIRED *** Special Requirements -------------------- All possible pedestal profile and fluctuation diagnostics Small NINJA D2 or He puff required for GPI Fluctuation diagnostics at high clock rates BES/Beam operators should check the miniprosal for special setup requirements | |
| Jul 3 2003 09:24:50:190AM | 1030703001 | Jim Irby | Note that the leak we have had for two days has been localized to G-HOR on one of the TS actuators. We will purge with helium for this run. Loaded 1030702013 into seg 2. Left seg 1 from 1030702040. Inner gap will have to be adjusted after first shot to match 1000927915 which is the model EDA shot Copied seg 2 of 1000928015 into seg 3 Copied/Pasted TF current from seg 3 to seg 2 Seg 3 is off Plasma for 1.12 s --- no EDA |
| Jul 3 2003 10:01:22:340AM | 1030703002 | Jim Irby | Loaded NL_04 programming from seg 3 (1000928015) to seg 2. Density was too high last shot. Changed CLEARIN by +.005 m --- Brian would like inner gap to be .018 m. --------------- Plasma to 1 s CLEARIN now .015 m. --- will tweak out to .018 m for next shot |
| Jul 3 2003 10:25:32:643AM | 1030703003 | Jim Irby | Raised density a little to better match 1000928015 Dropped current by 20 kA increased CLEARIN by another .002 m ------------------- Plasma to 1 s again next shot we will reload the old shot |
| Jul 3 2003 10:44:26:987AM | 1030703004 | Jim Irby | Loaded 1000928015 into seg 2. Did recals on all the lines (with Wolfe help) Plasma for 1.14 s --- a little better --- an early h-mode |
| Jul 3 2003 11:07:24:537AM | 1030703005 | Jim Irby | Min Bt from -2.6 to -2.7 T Decreased CLEARIN by .002 m --- better match for inner wall scanning probe Helium gas bottle purging leak at G-Hor ran out of gas Fizzle ----- either previous disruption or leak?? We are delaying the run to replace the helium bottle.... |
| Jul 3 2003 11:33:43:250AM | 1030703006 | Jim Irby | Helium bottle replaced --- now under better regulation No PCS changes plasma to 1.25 s --- a little better -- h-mode at 1.0 s looks like Brian has the inner gap he needs Bt was a little too negative for Martin -- about 2.8 vs 2.7 that he asked for |
| Jul 3 2003 11:47:41:817AM | 1030703007 | Jim Irby | Dropped TF by 10 kA Operator error --- started INIT before TF change was loaded Plasma for 1.18 s --- late/weak h-mode |
| Jul 3 2003 12:09:46:743PM | 1030703008 | Jim Irby | Tf no longer ramping back up after 1 s. Just rampdown and hold --- will it still disrupt? Plasma to 1.23 s --- no better than earlier shots H-mode starts at 1.1 but goes away by 1.18 s |
| Jul 3 2003 12:28:55:520PM | 1030703009 | Jim Irby | Dropped NL_04 request by about 10% from 6.2 to 5.6e19 / m^2 plasma for 1.25 s --- h-mode starting 1.11 s very little change in nl_04 --- pre-programmed gas? |
| Jul 3 2003 12:37:36:270PM | 1030703010 | Jim Irby | Eliminated preprogrammed gas on PG3 plasma for 1.23 s --- short h-mode got lower density but h-mode worse and discharge length shorter |
| Jul 3 2003 12:57:52:707PM | 1030703011 | Jim Irby | CLEARIN reduced by another .002 m ---- give Brian a .014 m inner gap Reduced argon from 30 ms to 6 ms plasma for 1.25 s --- weak h-mode |
| Jul 3 2003 01:15:33:687PM | 1030703012 | Jim Irby | Changed RXL and ZXL to move the plasma in and up about 1 cm. There was a 1 cm jerk in ZXL around the time of the disruption. Reduced CLEARIN another 2 mm for Brian. plasma for 1.29 s --- a record, but no h-mode |
| Jul 3 2003 01:23:46:980PM | 1030703013 | Jim Irby | Ip from -800 to -840 kA plasma 0.7 s --- try decreasing Ip next |
| Jul 3 2003 01:40:29:227PM | 1030703014 | Jim Irby | Ip from 840 to 760 kA plasma for 1.4 s --- longest yet, but no h-mode |
| Jul 3 2003 02:05:47:263PM | 1030703015 | Jim Irby | Reload 1030703009 --- longest lasting h-mode loaded 1030703014 CLEARIN into seg 2 --- keep Brian's inner gap plasma for 1.15 s ---- |
| Jul 3 2003 02:11:30:803PM | 1030703016 | Jim Irby | Reloaded ramp up from shot 1030703003 plasma for 1.15 s --- will reload shot from yesterday next just to get a plasma. |
| Jul 3 2003 02:31:33:820PM | 1030703017 | Jim Irby | Loaded shot 1030702013 into seg 2 --- still has a ramp down to 4.5 T plasma into rampdown ---- rampdown more on next shot |
| Jul 3 2003 02:39:40:440PM | 1030703018 | Jim Irby | TF ramped down to 95 kA (3.5 T) by 0.9 s plasma into rampdown --- some dithering past 1.2 s |
| Jul 3 2003 03:02:12:163PM | 1030703019 | Jim Irby | TF from 3.5 to 3.0 T nl04 from 8.5e19 to 7.0e19 / m^2 plasma for 1.37 s --- no sign of h-modes |
| Jul 3 2003 03:14:12:853PM | 1030703020 | Jim Irby | Rampdown to 3.0 T sooner nl04 to 8.0e19 / m^2 plasma for 1.42 s ---- h-mode next shot lower density |
| Jul 3 2003 03:37:03:623PM | 1030703021 | Jim Irby | nl04 from 8e19 to 6e19 / m^2 reloaded CLEARIN from shot 14 for Brian into seg 2. plasma for 1.38 s --- looks like the inner gap was very wrong?? |
| Jul 3 2003 03:53:49:243PM | 1030703022 | Jim Irby | reloaded shot 20 into seg 2. plasma for 1.36 s --- next shot drop the density (really) |
| Jul 3 2003 04:08:44:233PM | 1030703023 | Jim Irby | nl04 from 8 to 6 e19 / m^2 plasma for 1.13 s --- weak, late h-mode |
| Jul 3 2003 04:22:11:850PM | 1030703024 | Jim Irby | Added A-coil starting at 0.4 s ramping to 4000A at .6 s plasma into rampdown (Thank you Bob Granetz for suggesting the a-coil) |
| Jul 3 2003 04:31:54:457PM | 1030703025 | Jim Irby | Loaded seg 2 TF programming from 1000928015 into seg 2 plasma to 1.05 s --- rampdown to low? |
| Jul 3 2003 04:49:00:797PM | 1030703026 | Jim Irby | TF min from 2.7 to 3.2 T plasma into rampdown but no h-mode |
| Jul 3 2003 05:00:44:393PM | 1030703027 | Jim Irby | Dropped TF min to 2.9 from 3.2 T plasma into rampdown --- h-modes starting 1.18 s |
| Engineering Operator Comments | ||||
| Shot | Time | Type | Status | Comment |
| 1 | 09:07:00:400AM | Plasma | Ok | |
| 2 | 09:35:22:740AM | Plasma | Ok | |
| 3 | 10:03:47:813AM | Plasma | Ok | |
| 4 | 10:25:54:460AM | Plasma | Ok | |
| 5 | 10:50:03:167AM | Plasma | Ok | |
| 6 | 11:17:42:973AM | Plasma | Ok | |
| 7 | 11:37:26:003AM | Plasma | Ok | |
| 8 | 11:59:04:350AM | Plasma | Ok | |
| 9 | 12:15:52:783PM | Plasma | Ok | |
| 10 | 12:31:06:307PM | Plasma | Ok | |
| 11 | 12:50:46:820PM | Plasma | Ok | |
| 12 | 01:06:05:593PM | Plasma | Ok | |
| 13 | 01:19:00:317PM | Plasma | Ok | |
| 14 | 01:32:03:790PM | Plasma | Ok | |
| 15 | 01:45:58:017PM | Plasma | Ok | |
| 16 | 02:07:19:970PM | Plasma | Ok | |
| 17 | 02:20:01:130PM | Plasma | Ok | |
| 18 | 02:33:41:463PM | Plasma | Ok | |
| 19 | 02:50:53:223PM | Plasma | Ok | |
| 20 | 03:07:01:547PM | Plasma | Ok | |
| 21 | 03:20:29:630PM | Plasma | Ok | |
| 22 | 03:37:45:110PM | Plasma | Ok | |
| 23 | 03:53:11:320PM | Plasma | Ok | |
| 24 | 04:09:42:720PM | Plasma | Ok | |
| 25 | 04:23:12:663PM | Plasma | Ok | |
| 26 | 04:35:55:463PM | Plasma | Ok | |
| 27 | 04:50:23:377PM | Plasma | Ok | |
| 28 | 05:03:04:537PM | Plasma | Ok | |