| Miniproposals | ||||||||||
|
| Operators | |
| Session leader(s): | Yijun Lin |
| Physics operator(s): | Joseph Snipes,Robert Granetz |
| Engineering operator(s): | Bill Byford,Bill Parkin |
| Engineering Operator Run Comment |
| MP 417 Post-Boronization evaluation |
| Session Leader Plans |
| Entered: Jun 10 2005 08:08:05:177AM |
| Author: Yijun Lin |
| SL_PLAN: 1050610 (same as 1050503)
MP 417. Post-boronization evaluation Setup: Li pellet and boron injectors may be needed. Run load shot 1050426022 (possibly at a slightly different density) Posssibly an extended run to 9 pm. Background: Boronization done preferentially to the outer limiter and antennas. ECDC in D2 prior to the first plasma (scan from 50 cm to 103 cm with dwell at 78.5 cm) We already know that this boronization would be effective based on some post Titanium runs. We still need to know whether it is as effective as the previous two boronizations, 1050419 (outer divertor only) and 1050425 (outer divertor together with outer limiter and antennas) Goal 1. Evaluate boronization by running constant discharges. 2. Evaluate the trend of impurities levels in the plasma Plan: 1. Load shot 1050426022. Slightly modified RF waveform. 3 MW from 0.7 to 1.1 sec, 4 MW (if possible, otherwise, 3.6 MW) from 1.1 sec to 1.5 sec Do a density scan in the first 3 shots, target density at nl = 1.1, 0.9, 1.3e20 m^-2. For the subsequent shots, choose the density that give the best long EDA H-mode Assess the boronization effectiveness using the first 15 plasmas. 2. Decision point (after 15 full-length plasmas). A. If the performance is excellent (Wtot >= 170 kJ at 3 MW RF), we will continue running the same 1 MA plasmas until we see definite degradation of performance. (criterion: Wtot <~ 150 kJ at 1 MA and 3 MW Prf.) the run will stop as soon as there are three consecutive plasmas meeting the degradated performance criterion. In this case, we possibly run until 9 pm. No boronization will be followed. B. If the boronization has worn out substantially after 15 plasmas (150 kJ < Wtot < 165 kJ at 3 MW, 1 MA), we will continue 1 MA shot until we see three plasmas with Wtot <~ 150 kJ at 3 MW and 1 MA. If time allows (earlier than 5 pm), we will try boron shaker to inject boron to the outer limiter. We will also try Li-pellet injection. And see whether there is an improvement on the performance. In this case, the run will probably stop at 5 pm. No boronization will be followed. C. (This scenario is unlikely based on the experience we have now) If the boronization is shown to be a "bust" (3 consecutive plasmas at Wtot < 150 kJ at 1 MA, 3 MW Prf), we will try the boron shaker and Li-pellet injections. We may also do N2 puff into RF heated L-mode and identify the dominant Mo sources. In this case, the run will definitely stop at 5 pm. |
| Physics Operators Plans |
| Entered: Jun 9 2005 11:35:28:080PM |
| Author: Joseph Snipes |
| Engineering setup for Friday, 10 June 2005
MP #417: Post-boronization evaluation Session leader: Y. Lin Physics operator: J. Snipes Overnight boronization with the following parameters: . dP of 120 to 140 psi . scan from 50 cm to 103 cm with dwell at 78.5 cm ECDC in D2 prior to first plasma discharge Run begins at 09:00 and ends at 21:00. Power systems as on 1050608021 (1.0 MA, 5.4 T, SNL fiducial) A-coil configuration: normal [+Dtop -Dbot -Jtop +Jbot] and enabled. Gas Setup: fill B-Top with 6 psi D2 Hybrid enabled (PG4) fill B-side lower with 1 psi Ar Hybrid DISABLED (PG1) leave B-side upper with whatever Hybrid disabled fill B-main (C-side) with 30 psi D2 Hybrid enabled (PG3) NINJA not used today Enable the following gate valves and shutters, assuming no vacuum problems: ECE, VUV, Z-bolo shutters ------------------------------------------------------------------------------- ICRF Setup: All transmitters in run on at 08:30. ------------------------------------------------------------------------------- Plan: see SL_PLAN |
| Session Leader Summaries |
| Entered: Jun 13 2005 03:46:51:317PM |
| Author: Yijun Lin |
| A successful run. Total 48 shots, in which about 30 shots have at
least 3 MW RF. Performance peaked at about shot 20, Wtot 210 kJ at 4 MW and 170 kJ at 3 MW. The flat top of performance last for about 8 plasmas for 4 MW and about 15 plasmas for 3 MW, then definite deterioration was observed. After shot 40, the performance went to be marginally 'good', Wtot ~ 150 kJ at 3 MW. Also starting from this point, 4 MW and 3 MW gave about the same Wtot. After shot 47, the performance is below 'good performance', with Wtot < 150 kJ. The last shot, shot 48, only got 136 kJ at 3 MW. H/D level was 4-6% all day. Mo level was significantly lower than pre-boronization. Ti is also insignificant, although visible. Prad crept up shot by shot slowly, and finally deteriorate the performance. The total neutrons today is 5.7e14. 2nd highest in C-Mod history. |
| Physics Operator Summaries |
| Entered: Jun 10 2005 05:02:09:010PM |
| Author: Joseph Snipes |
| The machine ran well but there were a number of difficulties maintaining the breakdown after the boronization. I was physop up through shot 30 and there were 20 plasmas, 3 fizzles, and 7 duds. The plasmas that went were all full length with RF and good performance except for shot 15 which disrupted just after the start of the RF due to overheating of the divertor, apparently the Tungsten brush tiles. The boronization kept up until at least shot 30 with a number of plasmas exceeding 200 kJ and a neutron alert by mid afternoon. So, the run continued until 9:00 pm. Granetz took over as physop after 5:00 pm. |
| Entered: Jun 10 2005 09:30:01:590PM |
| Author: Robert Granetz |
| Physop summary for latter part of Friday 10 June 2005:
MP #417: How long does boronization last? Session leader: Y. Lin/S. Wukitch Physics operator: R. Granetz I took over as physop from Joe Snipes after shot 30. We continued running 1 MA, 5.4 T, SNL fiducial plasmas for the RF, with the goal of finding out if/when the good confinement afforded by last night's boronization would wear off. It clearly did wear off as the run progressed, starting first at the 5 MW level, then the 4 MW level, and finally even the 3 MW level. See Yijun's session leader summary for details. After I took over, the machine ran well until we had a disruption (confirmed moly injection) on shot 35. Then there were four duds over the next 6 shots. After tweaking Bz0, the remainder of the run went well. Oh yes, there is one other important conclusion from today's run. Although we had an air leak earlier this week (6 torr on a humid Monday morning) a single day's bake brought the machine right back to its pre-leak condition. Scorecard: 34 plasmas 3 fizzles 11 duds (2 due to power supply problems) 0 tests or no-power shot cycles ---------- 48 total shot cycles |
| Session Leader Comments | |||
| Jun 10 2005 10:15:08:630AM | 1050610001 | Yijun Lin | fizzle |
| Jun 10 2005 11:40:34:333AM | 1050610003 | Yijun Lin | Plasma, 5.4 T, 1 MA, target nl 1e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma (not counted for the MP) Little RF power due to mismatching. Next: repeat. |
| Jun 10 2005 10:15:23:943AM | 1050610004 | Yijun Lin | fizzle |
| Jun 10 2005 11:40:42:083AM | 1050610005 | Yijun Lin | Plasma, 5.4 T, 1 MA, target nl 1e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma (not counted for the MP) Little RF power due to mismatching on E and too high neutral pressure for J. Next: repeat. |
| Jun 10 2005 10:47:43:067AM | 1050610006 | Yijun Lin | dud |
| Jun 10 2005 10:59:30:317AM | 1050610007 | Yijun Lin | fizzle |
| Jun 10 2005 11:40:13:567AM | 1050610008 | Yijun Lin | Plasma, 5.4 T, 1 MA, target nl 1e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. H-mode from E power only. J ant faulted due to high neutral pressure. H89 1.3, Wtot 110 kJ at 0.8 MW. Next: repeat. |
| Jun 10 2005 11:40:04:630AM | 1050610009 | Yijun Lin | Plasma, 5.4 T, 1 MA, target nl 1e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. Hmode. J port was still troubling at neutral pressure. Wtot 115 kJ at 1.3 MW. H89 1.3 Next: repeat. |
| Jun 10 2005 11:41:57:943AM | 1050610010 | Yijun Lin | Plasma, 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. Hmode. J port was still troubling at neutral pressure. Next: lower target density to 0.8e20, so that we can expediate the reduction of neutral pressure to help J antenna to run. |
| Jun 10 2005 11:57:34:630AM | 1050610011 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl .8e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. Hmode. Wtot = 140 kJ at 3 MW. Wtot was still rising while J port faulted out due to mismatch. Next: repeat |
| Jun 10 2005 12:09:26:600PM | 1050610012 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl .8e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. Long EDA Hmode. Wtot = 155 kJ at 3 MW. Wtot was still rising while J port faulted out Next: go back to nl 1.0. |
| Jun 10 2005 12:24:54:960PM | 1050610013 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.8 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. Long EDA Hmode. 140 kJ @ 3.0 MW Next: |
| Jun 10 2005 12:43:08:833PM | 1050610014 | Yijun Lin | dud
Cell and power room access, for H/D, DNB, and RF. FMIT #1 came back with no reason. It is now on run-on and probably be ready for next shot. |
| Jun 10 2005 01:04:10:130PM | 1050610015 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 3.7 MW total, [1.1, 1.5] sec from J + E antennas. result: plasma. disrupted 0.76 sec. H/D 4% Next: have D port power. |
| Jun 10 2005 01:25:28:583PM | 1050610016 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 161 kJ @ 3.0 MW. H89 = 1.5 next: repeat. |
| Jun 10 2005 01:28:27:100PM | 1050610017 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 177 kJ @ 3.1 MW, H89 1.6 201 kJ @ 3.8 MW. H89 1.8 next: repeat. main pump gate valve will be closed for next shot. |
| Jun 10 2005 01:41:20:943PM | 1050610018 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 177 kJ @ 3.0 MW 201 kJ @ 3.7 MW main pump gate valve closed for 300 secs for Blip on wall study. next: repeat. gate valve open. |
| Jun 10 2005 02:16:21:117PM | 1050610019 | Yijun Lin | dud. (possibly related to the gate valve closing in shot 18)
I will close the gate valve less frequently or until I get reasonable number of good plasmas. Delay due to camac highway problems. (J. Bosco is working on it). |
| Jun 10 2005 02:33:01:397PM | 1050610020 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. (long delay for highway work. No camac highway 5. No neutron data, H/D, HIREX, and gas pressure data) 154 kJ @ 3.0 MW 203 kJ @ 4.1 MW next: repeat. |
| Jun 10 2005 03:03:55:147PM | 1050610020 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 154 kJ @ 3.0 MW. E port faulted in the early part of H-mode 203 kJ @ 4.1 MW (long delay for highway work. No camac highway 5. No neutron data, H/D, HIREX, and gas pressure, and some bolometry data.) Wait until the highway is fixed before attempting next plasma. Temporarily, only the following data are available on highway 5: Gas and neutrons, and some spectroscopic data. |
| Jun 10 2005 03:03:29:647PM | 1050610021 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 154 kJ @ 3.1 MW. Wtot was still rising when J faulted. 209 kJ @ 4.1 MW next: repeat |
| Jun 10 2005 03:20:57:747PM | 1050610022 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. (injection at 1.2 sec, but plasma performance recovered) 173 kJ @ 3.1 MW (this time, there was no antenna trip while Wtot was rising) 202 kJ @ 4.1 MW H/D 4-5% next: repeat |
| Jun 10 2005 03:28:33:213PM | 1050610023 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 164 kJ @ 3.1 MW (E faulted during Wtot rising) 199 kJ @ 4.1 MW next: repeat |
| Jun 10 2005 03:42:13:480PM | 1050610024 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 164 kJ @ 3.1 MW (J and E clean) 202 kJ @ 4.1 MW next: repeat |
| Jun 10 2005 03:51:51:357PM | 1050610025 | Yijun Lin | dud.
Next: disable Ar. Note Ar has been puffed in since shot 13. |
| Jun 10 2005 04:04:26:010PM | 1050610026 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 163 kJ @ 3.1 MW (J and E a few faults) 195 kJ @ 4.1 MW next: repeat |
| Jun 10 2005 04:27:18:777PM | 1050610027 | Yijun Lin | dud.
TF signals showed only 0.3 T. PCS problem. |
| Jun 10 2005 04:32:04:857PM | 1050610028 | Yijun Lin | dud. EF3 breaker pulled |
| Jun 10 2005 04:51:03:403PM | 1050610029 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 167 kJ @ 3.0 MW 181 kJ @ 3.9 MW (too many faults) next: repeat. with gate valve closed for 5 mins |
| Jun 10 2005 05:12:40:670PM | 1050610030 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.1] sec from J + E antennas 4.0 MW total, [1.1, 1.5] sec from J + E + D antennas. result: plasma. 160 kJ @ 3.1 MW 194 kJ @ 4.2 MW gate valve closed for 5 minutes this shot. next: repeat with gate valve open |
| Jun 10 2005 05:17:30:653PM | 1050610031 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. J faulted all the way. Neutral pressure seems to be OK. I can only blame the gate valve closing (But how?) next: repeat |
| Jun 10 2005 05:28:12:700PM | 1050610032 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 167 kJ @ 3.1 MW 189 kJ @ 4.3 MW 206 kJ @ 5.0 MW next: repeat |
| Jun 10 2005 05:41:44:607PM | 1050610033 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 154 kJ @ 3.0 MW (both E and J had faults) 157 kJ @ 3.8 MW (Just too many faults) next: repeat |
| Jun 10 2005 05:56:48:967PM | 1050610034 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 163 kJ @ 3.1 MW. (still OK) 166 kJ @ 4.0 MW, (this one is getting lower without obvious injection, only with D faulting) 182 kJ @ 4.9 MW next: repeat |
| Jun 10 2005 06:05:34:497PM | 1050610035 | Yijun Lin | early disruption at 0.35 sec. |
| Jun 10 2005 06:18:37:620PM | 1050610036 | Yijun Lin | dud |
| Jun 10 2005 06:32:51:683PM | 1050610037 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 144 kJ @ 3.0 MW (faults on both E and J) 178 kJ @ 4.1 MW next: repeat |
| Jun 10 2005 06:43:08:480PM | 1050610038 | Yijun Lin | dud |
| Jun 10 2005 07:01:25:573PM | 1050610039 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas J antenna was programmed to be off between 1.25 and 1.35 sec for bolometry comparison. result: plasma. (3 H-modes instead of 1 long EDA) 156 kJ @ 3.1 MW next: repeat (no more notch on J) |
| Jun 10 2005 07:15:09:980PM | 1050610040 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. (1 long EDA) 155 kJ @ 3.0 MW (two shots in a row, just above 150 kJ. we are riding the downtrend). 155 kJ @ 4.1 MW (no more gain at higher power). 165 kJ @ 4.9 MW next: repeat |
| Jun 10 2005 07:22:00:573PM | 1050610041 | Yijun Lin | dud |
| Jun 10 2005 07:35:48:963PM | 1050610042 | Yijun Lin | dud. two in a row. |
| Jun 10 2005 08:07:13:683PM | 1050610043 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. (1 long EDA) 149 kJ @ 3.1 MW (Wtot < 150 kJ at clean RF at 3 MW. Definitely rolled-over) 148 kJ @ 4.1 MW 166 kJ @ 4.8 MW next: repeat |
| Jun 10 2005 08:08:44:887PM | 1050610044 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. (1 long EDA) 157 kJ @ 3.0 MW (somewhat higher. Is it because J port started up later?) 149 kJ @ 4.1 MW 164 kJ @ 4.8 MW next: repeat |
| Jun 10 2005 08:19:34:980PM | 1050610045 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. J faulted out in the beginning, probably due to neutral pressure. next: repeat. Start J port at 0.8 sec to increase the chance for it to run. |
| Jun 10 2005 08:32:46:170PM | 1050610046 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl 1.e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. J port faulted out. I suspect the neutral pressure is still too high for J. next: lower target density at 0.9e20 and still start up J at 0.8 sec. |
| Jun 10 2005 08:48:40:530PM | 1050610047 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl .9e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 4 H-modes. J ran at this reduced target density. 140 kJ @ 3.0 MW 142 kJ @ 3.9 MW 156 kJ @ 4.6 MW next: repeat (will be the last shot for this extended run) |
| Jun 10 2005 09:00:47:090PM | 1050610048 | Yijun Lin | Plasma: 5.4 T, 1 MA, target nl .9e20 m^-2, LSN, deuterium plasma.
RF: 3 MW total, [0.7, 1.05] sec from J + E antennas 4.0 MW total, [1.05, 1.3] sec from J + E + D antennas. 5 MW total demand [1.3, 1.5] sec from J + E + D antennas result: plasma. 136 kJ @ 2.9 MW (now it is at the level of mediocre/bad performance). 142 kJ @ 3.9 MW End of run |
| Physics Operator Comments | |||
| Jun 10 2005 09:47:46:117AM | 1050610001 | Joseph Snipes | Shot 1: Copied shot 1050426022 and then removed the pre-programmed deuterium gas puff in segment 2. Copied segment 1 from shot 1050609027 to get yesterday's startup. Since boronization may increase the gas from the walls, I reduced the prepuff from 36 ms to 30 ms duration. Delay before shot 1 to repair the ratiomatic pressure gauge. |
| Jun 10 2005 09:48:07:913AM | 1050610001 | Joseph Snipes | Shot 1: Copied shot 1050426022 and then removed the pre-programmed deuterium gas puff in segment 2. Copied segment 1 from shot 1050608021 for the startup. Fizzle! |
| Jun 10 2005 09:49:30:960AM | 1050610002 | Joseph Snipes | Shot 2: Ratiomatic filament was changed, so there could be a calibration error. Assume the calibration is OK and that the boronization loaded the walls. So, I've dropped the prepuff by a factor of two to 14 ms duration. Dud! |
| Jun 10 2005 10:06:14:710AM | 1050610003 | Joseph Snipes | Shot 3: Add 6 ms more prepuff to 20 ms duration. Good shot. Late breakdown at 8 ms, but otherwise the startup looks decent. |
| Jun 10 2005 11:19:15:490AM | 1050610004 | Joseph Snipes | Shot 4: Add 6 ms more prepuff to 20 ms duration. Fizzle! |
| Jun 10 2005 10:43:06:037AM | 1050610005 | Joseph Snipes | Shot 5: Reduced prepuff by 2 ms to 18 ms duration and reduced Br0 by 0.25 mT
to 0 mT. Good shot. |
| Jun 10 2005 10:47:59:053AM | 1050610006 | Joseph Snipes | Shot 6: Reduced prepuff to 17 ms duration. Dud! |
| Jun 10 2005 10:59:28:677AM | 1050610007 | Joseph Snipes | Shot 7: Increased prepuff by 4 ms to 21 ms duration. Fizzle! |
| Jun 10 2005 11:12:16:240AM | 1050610008 | Joseph Snipes | Shot 8: Reduced prepuff by 1 ms to 20 ms duration. Good shot. |
| Jun 10 2005 11:34:07:880AM | 1050610009 | Joseph Snipes | Shot 9: Extended Ip out to 1.5 s at 1.05 MA. Reduced prepuff by 1 ms to 19 ms duration. Good shot.
|
| Jun 10 2005 11:39:36:443AM | 1050610010 | Joseph Snipes | Shot 10: Reduced prepuff by 1 ms to 18 ms duration. Good shot.
|
| Jun 10 2005 11:50:41:240AM | 1050610011 | Joseph Snipes | Shot 11: Reduced nl04 to 0.8 x 10^20 m^-2. Good shot. |
| Jun 10 2005 12:08:47:117PM | 1050610012 | Joseph Snipes | Shot 12: Repeat. Good shot. Nice long EDA H-mode even though RF did not stay on.
|
| Jun 10 2005 12:19:13:523PM | 1050610013 | Joseph Snipes | Shot 13: Returned to nl04 = 1.05 x 10^20 m^-2. Enabled Ar gas puff from 0.3 to 0.33 s. Good shot. |
| Jun 10 2005 12:32:34:740PM | 1050610014 | Joseph Snipes | Shot 14: Increased Ar puff to 50 ms duration from 0.3 to 0.35 s. Dud! |
| Jun 10 2005 01:03:06:553PM | 1050610015 | Joseph Snipes | Shot 15: Decreased EF4 current from -1280 A to -1295 A. Increased prepuff by 1 ms to 19 ms duration. Disrupted at 0.76 s. Molten metal spews forth on WIDE2 camera view from the area of the Tungsten brush tiles in the lower outer divertor. |
| Jun 10 2005 01:10:11:490PM | 1050610016 | Joseph Snipes | Shot 16: Repeat. Good shot. |
| Jun 10 2005 01:26:28:693PM | 1050610017 | Joseph Snipes | Shot 17: Asked to close the main pump gate valve after the next shot for Bruce.
But, the directions were not heeded. Good shot. |
| Jun 10 2005 01:34:23:460PM | 1050610018 | Joseph Snipes | Shot 18: Asked once again to close the gate valve after shot 18. Good shot. |
| Jun 10 2005 01:46:56:147PM | 1050610019 | Joseph Snipes | Shot 19: Gate valves re-enabled to stay open after shot 19. Increased Ar puff duration to 70 ms at John's request. Dud! |
| Jun 10 2005 02:32:05:537PM | 1050610020 | Joseph Snipes | Shot 20: Added 2 ms to the prepuff to make it 21 ms duration. Good shot. Over 200 kJ with 4 MW of ICRF. |
| Jun 10 2005 03:01:33:367PM | 1050610021 | Joseph Snipes | Shot 21: Repeat. Good shot. |
| Jun 10 2005 03:09:00:287PM | 1050610022 | Joseph Snipes | Shot 22: Reduced EF4 current by 10 A to -1305 A. Good shot. |
| Jun 10 2005 03:23:27:760PM | 1050610023 | Joseph Snipes | Shot 23: Repeat. Good shot. |
| Jun 10 2005 03:41:41:933PM | 1050610024 | Joseph Snipes | Shot 24: Repeat. Good shot. |
| Jun 10 2005 03:49:33:277PM | 1050610025 | Joseph Snipes | Shot 25: Repeat. Dud! |
| Jun 10 2005 04:10:17:510PM | 1050610025 | Joseph Snipes | Shot 26: Increased EF4 current by 15 A to -1290 A. Good shot. |
| Jun 10 2005 04:28:02:730PM | 1050610027 | Joseph Snipes | Shot 27: Reduced prepuff by 2 ms to 19 ms duration. Power supply fault. Very low TF at 0.3 T. Apparently, my load into model was a second too late. |
| Jun 10 2005 04:32:12:747PM | 1050610028 | Joseph Snipes | Shot 28: Try again. Dud. EF3 breaker pulled out. |
| Jun 10 2005 04:47:14:060PM | 1050610029 | Joseph Snipes | Shot 29: In case there is still something wrong with the hybrid setup, I've reloaded shot 1050610026. We will try another shot. Good shot. |
| Jun 10 2005 05:03:36:030PM | 1050610030 | Joseph Snipes | Shot 30: Gate valve to be closed after this shot. Good shot. |
| Jun 10 2005 05:09:16:920PM | 1050610031 | Robert Granetz | Granetz taking over as physics operator prior to this shot. |
| Jun 10 2005 05:19:53:670PM | 1050610031 | Robert Granetz | Plasma. Good shot. Breakdown pressure came down, but it's still higher than
usual. Torus gate valve remained open for this shot, and will remain open for the rest of tonight's shots. Prf=1-1.5 MW only. No power from J-port. Wth=110 kJ. Video cameras are not working. H/(H+D)=4%. Next shot: repeat, no changes. The goal is to see if/when the effects of boronization wear off. |
| Jun 10 2005 05:51:33:730PM | 1050610032 | Robert Granetz | Plasma. Good shot. Prf=4+ MW. Wth=185-200 kJ. H/(H+D)=4.5%.
Next shot: reduce pre-fill gas pulse to 20 ms. |
| Jun 10 2005 05:50:53:823PM | 1050610033 | Robert Granetz | Plasma. Good shot. Prf=3-4 MW. Wth=150 kJ. H/(H+D)=4-5%
Next shot: repeat, no changes |
| Jun 10 2005 06:01:10:090PM | 1050610034 | Robert Granetz | Plasma. Good shot. Prf=4+ MW. Wth=150-175 kJ. H/(H+D)=4-5%
Next shot: repeat, no changes |
| Jun 10 2005 06:35:08:403PM | 1050610035 | Robert Granetz | Plasma. Disrupted early (t=0.35) due to molybdenum injection. This is only
the second disruption of the day so far. Next shot: try again, no changes. |
| Jun 10 2005 06:34:42:933PM | 1050610036 | Robert Granetz | Dud. Inexplicable. All the traces overlay. Null looks good.
Maybe it has something to do with the preceding disruption. Next shot: no changes, just try again. |
| Jun 10 2005 06:37:32:217PM | 1050610037 | Robert Granetz | Plasma. Good shot. Prf=3-4 MW. Wth=150 kJ. H/(H+D)=5%.
Late breakdown. Next shot: no changes. |
| Jun 10 2005 06:43:36:683PM | 1050610038 | Robert Granetz | Dud. Null is fine.
Next shot: increase pre-fill by 2 ms. |
| Jun 10 2005 07:01:34:090PM | 1050610039 | Robert Granetz | Plasma. Good shot. J-port was intentionally turned off for 0.5 s to
investigate bolometry and molybdenum measurements. At 3 MW, Wth=150 kJ. H/(H+D)=4%. Next shot: no changes. |
| Jun 10 2005 07:16:11:857PM | 1050610040 | Robert Granetz | Plasma. Good shot. Prf = 3 -> 4 -> 4+ MW. Wth=150 kJ. H/(H+D)=5%.
Seems like the extra RF power above 3 MW is not increasing the stored energy at all. Next shot: no changes. |
| Jun 10 2005 07:24:03:310PM | 1050610041 | Robert Granetz | Dud.
Next shot: add another 2 ms to pre-fill. |
| Jun 10 2005 07:39:29:590PM | 1050610042 | Robert Granetz | Dud.
Next shot: add -15 amps from IC_EF4 (-1290 -> -1305) |
| Jun 10 2005 07:53:22:963PM | 1050610043 | Robert Granetz | Plasma. Good shot. Prf = 3 -> 4 -> 4+ MW. Wth=150 kJ at best. H/(H+D)=4.5-5%.
Performance is degrading, even at 3 MW. Next shot: repeat, no changes. |
| Jun 10 2005 08:10:54:433PM | 1050610044 | Robert Granetz | Plasma. Good shot. Prf = 3 -> 4 -> 4+ MW. Wth=150 kJ at best. H/(H+D)=4.5-5%.
Performance is degrading, even at 3 MW. Next shot: repeat, no changes. |
| Jun 10 2005 08:23:41:747PM | 1050610045 | Robert Granetz | Plasma. Good shot. But no power from J-port.
Next shot: repeat, no changes. |
| Jun 10 2005 08:33:52:527PM | 1050610046 | Robert Granetz | Plasma. Good shot. No power from J-port, again.
Next shot: lower nl_04 to 0.9e20 m-2 (from 1.05e20 m-2) to try and get J-port going again. |
| Jun 10 2005 08:49:48:840PM | 1050610047 | Robert Granetz | Plasma. Good shot. Prf = 3 -> 4 -> 4+ MW. Wth=130-150 kJ. H/(H+D)=4.5-5%.
Turnover in performance is obvious, even at 3 MW. Next shot: repeat, no changes. |
| Jun 10 2005 09:03:52:370PM | 1050610048 | Robert Granetz | Plasma. Good shot. Prf = 3 -> 4 MW. Wth=130 kJ. H/(H+D)=4.5%.
End of run. |
| Engineering Operator Comments | ||||
| Shot | Time | Type | Status | Comment |
| 1 | 09:31:29:740AM | Plasma | Ok | |
| 2 | 09:48:08:367AM | Plasma | Ok | |
| 3 | 10:00:40:740AM | Plasma | Ok | |
| 4 | 10:13:45:897AM | Plasma | Ok | |
| 5 | 10:26:44:287AM | Plasma | Ok | |
| 6 | 10:45:38:147AM | Plasma | Ok | |
| 7 | 10:58:08:617AM | Plasma | Ok | |
| 8 | 11:10:56:787AM | Plasma | Ok | |
| 9 | 11:23:37:630AM | Plasma | Ok | |
| 10 | 11:36:30:817AM | Plasma | Ok | |
| 11 | 11:49:18:007AM | Plasma | Ok | |
| 12 | 12:03:04:617PM | Plasma | Ok | |
| 13 | 12:17:27:647PM | Plasma | Ok | |
| 14 | 12:31:09:223PM | Plasma | Ok | |
| 15 | 12:54:02:227PM | Plasma | Ok | |
| 16 | 01:06:45:240PM | Plasma | Ok | |
| 17 | 01:19:23:083PM | Plasma | Ok | |
| 18 | 01:32:56:617PM | Plasma | Ok | |
| 19 | 01:45:38:257PM | Plasma | Ok | |
| 20 | 02:28:05:193PM | Plasma | Ok | |
| 21 | 02:55:06:943PM | Plasma | Ok | |
| 22 | 03:07:41:333PM | Plasma | Ok | |
| 23 | 03:22:12:417PM | Plasma | Ok | |
| 24 | 03:35:03:497PM | Plasma | Ok | |
| 25 | 03:47:46:043PM | Plasma | Ok | |
| 26 | 04:00:15:513PM | Plasma | Ok | |
| 27 | 04:12:40:167PM | Plasma | Bad | PLC Camac failure |
| 28 | 04:28:42:760PM | Plasma | Bad | EF3 Problem |
| 29 | 04:45:50:247PM | Plasma | Ok | |
| 30 | 04:58:27:247PM | Plasma | Ok | |
| 31 | 05:11:30:217PM | Plasma | Ok | |
| 32 | 05:23:51:230PM | Plasma | Ok | |
| 33 | 05:37:14:510PM | Plasma | Ok | |
| 34 | 05:50:17:963PM | Plasma | Ok | |
| 35 | 06:03:03:607PM | Plasma | Ok | |
| 36 | 06:16:12:120PM | Plasma | Ok | |
| 37 | 06:28:57:793PM | Plasma | Ok | |
| 38 | 06:41:39:823PM | Plasma | Ok | |
| 39 | 06:54:19:043PM | Plasma | Ok | |
| 40 | 07:07:36:607PM | Plasma | Ok | |
| 41 | 07:20:15:823PM | Plasma | Ok | |
| 42 | 07:33:56:920PM | Plasma | Ok | |
| 43 | 07:47:05:530PM | Plasma | Ok | |
| 44 | 08:00:03:823PM | Plasma | Ok | |
| 45 | 08:12:47:497PM | Plasma | Ok | |
| 46 | 08:25:16:747PM | Plasma | Ok | |
| 47 | 08:38:35:700PM | Plasma | Ok | |
| 48 | 08:56:13:670PM | Plasma | Ok | |