Alcator C-Mod Run 1060316 Information

Back to runs

Miniproposals
Miniproposal:409
Date Filed: 1/19/2005
Title:Phase Space of the Scrape-off-Layer Plasma
First Author:Brian Labombard
Session Leader:Brian Labombard (shots 1-18)

Operators
Session leader(s):Brian Labombard
Physics operator(s):Ron Parker,Bill Rowan,Ron Parker
Engineering operator(s):Bill Cochran,Bill Parkin

Engineering Operator Run Comment
MP#409: SOL Phase Space (9:00 to 16:00) MP#429 Turbulence in limited dis

Session Leader Plans
Entered: Mar 15 2006 05:53:21:680PM
Author: Brian Labombard
===========================
Engineering setup for Thursday 16 Mar 2006

MP#409: SOL Phase Space (9:00 to 16:00)
MP#429 Turbulence in limited discharges (16:00 to 17:00)

Session leader: B. Labombard
Physics operator: R. Parker

Overnight ECDC in D2, and bake at 60 C.

Run begins at 09:00 and ends at 17:00.

Power systems as on 1051123004 (0.8 MA, 5.4 T, lower single null)

A-coil configuration: normal [+Dtop -Dbot -Jtop +Jbot] and enabled.

Gas Setup:
fill B-Top with 6 psi D2 Hybrid enabled (PG4)
fill B-side lower with 1 psi Ar + 2 psi Ne Hybrid DISABLED (PG1)
leave B-side upper as is Hybrid DISABLED (PG2)
fill B-main (C-side) with 40 psi D2 Hybrid enabled (PG3)
fill NINJA with 10 psi D2 Leave DISABLED

Enable the following gate valves and shutters, assuming no vacuum problems:
ECE, VUV, Z-bolo shutters

Torvac setup: Gate valves open

ICRF Setup: No RF today.

Important Diagnostics:
ASP, FSP, ISP, Xybion camera, fast H-alpha diode array, Chromex, Edge TS

===================================
Run Plan for 1060316

MP#409 "SOL Phase space studies"

Overall Goal
Map out the 'phase space' of the SOL plasma, i.e. the relationships between
the 'transport state' (profile shapes, gradients, cross-field fluxes, advection
velocities, turbulence characteristics) and theory-based 'control parameters'
(local collisionality, magnetic field strengths, parallel connection length,...)
that may determine that state.

Today's Goals
The focus today is on getting some data at Ip=1.1 MA and Bt=5.4 Tesla in LSN and USN equilibria.
If there is time, we will also take data at Ip=0.8 MA and Bt=4.0 Tesla. First we will start out with a
few 0.8 MA shots to make contact with previous data.

Notes
- Set integration time on Xybion to 1 ms
- Connect the following fiber views for the fast diodes
Outer SOL views 1-3,5,7,9-14,31-40 (total of 21)
Innerwall SOL views B and C
- Connect the following fiber views for the CHROMEX
Outer SOL views 18-22,24-29 (total of 11)
Innerwall SOL views A,D,E,F - otherwise known as 1,4-6
- Set timing on fastdiode digitizers to 0.1 s after the A-B limiter NINJA puff timing

Plan
Load from shot#1051123004. This shot ran on segment#2. It was a LSN discharge
with Ip=0.8 MA, Bt= 5.4 tesla, NL04 = 0.79e20. Note: segment#3 has
a USN program that we will use (Segment#4 is double-null? will not be used today.)

ASP, FSP, ISP programmed to scan at 0.65, 0.85, 1.05 seconds
NINJA gas puff for GPI and boron V spectroscopy entering plasma at 1.1s
Set NINJA for D2 puff at A-B limiter and B016-001. Plenum pressure of 10 PSI.
Shots

Ip= 0.8 MA, NL04 = 0.6
1,2 LSN optimize probe insertion
3,4 USN optimize probe insertion

Ip= 1.1 MA, NL04 = 0.5
5,6 LSN optimize probe insertion
7,8 USN optimize probe insertion

NL04 = 0.8
9,10 USN
11,12 LSN

NL04 = 1.1
13,14 LSN
15,16 USN

NL04 = 1.4
17,18 USN
19,20 LSN

NL04 = 1.7
17,18 USN
19,20 LSN

If time remains...
Change to Bt=4T, Ip= 0.8 MA and continue LSN/USN sequence
NL04 = 0.6

NL04 = 0.4

NL04 = 0.8

NL04 = 1.0

NL04 = 1.2

Physics Operators Plans
Entered: Mar 15 2006 05:50:50:053PM
Author: Ron Parker
Engineering setup for Thursday 16 Mar 2006


MP#409: SOL Phase Space (9:00 to 16:00)
MP#429 Turbulence in limited discharges (16:00 to 17:00)


Session leader: B. Labombard MP 409; S. Zweben MP 429
Physics operator: R. Parker


Overnight ECDC in D2, and bake at 60 C.


Run begins at 09:00 and ends at 17:00.


Power systems as on 1051123004 (0.8 MA, 5.4 T, lower single null)


A-coil configuration: normal [+Dtop -Dbot -Jtop +Jbot] and enabled.


Gas Setup:
fill B-Top with 6 psi D2 Hybrid enabled (PG4)
fill B-side lower with 1 psi Ar + 2 psi Ne Hybrid DISABLED (PG1)
leave B-side upper as is Hybrid DISABLED (PG2)
fill B-main (C-side) with 40 psi D2 Hybrid enabled (PG3)
fill NINJA with 10 psi D2 Leave DISABLED


Enable the following gate valves and shutters, assuming no vacuum problems:
ECE, VUV, Z-bolo shutters


Torvac setup: Gate valves open


ICRF Setup: No RF today.


Important Diagnostics:
ASP, FSP, ISP, Xybion camera, fast H-alpha diode array, Chromex, Edge TS

Run Plan for 1060316

MP#409 "SOL Phase space studies"

Overall Goal
Map out the 'phase space' of the SOL plasma, i.e. the relationships between
the 'transport state' (profile shapes, gradients, cross-field fluxes, advection
velocities, turbulence characteristics) and theory-based 'control parameters'
(local collisionality, magnetic field strengths, parallel connection length,...)
that may determine that state.

Today's Goals
The focus today is on getting some data at Ip=1.1 MA and Bt=5.4 Tesla in
LSN and USN equilibria.
If there is time, we will also take data at Ip=0.8 MA and Bt=4.0 Tesla. First we
will start out with a
few 0.8 MA shots to make contact with previous data.

Notes
- Set integration time on Xybion to 1 ms
- Connect the following fiber views for the fast diodes
Outer SOL views 1-3,5,7,9-14,31-40 (total of 21)
Innerwall SOL views B and C
- Connect the following fiber views for the CHROMEX
Outer SOL views 18-22,24-29 (total of 11)
Innerwall SOL views A,D,E,F - otherwise known as 1,4-6
- Set timing on fastdiode digitizers to 0.1 s after the A-B limiter NINJA puff
timing

Plan
Load from shot#1051123004. This shot ran on segment#2. It was a LSN discharge
with Ip=0.8 MA, Bt= 5.4 tesla, NL04 = 0.79e20. Note: segment#3 has
a USN program that we will use (Segment#4 is double-null? will not be used
today.)

ASP, FSP, ISP programmed to scan at 0.65, 0.85, 1.05 seconds
NINJA gas puff for GPI and boron V spectroscopy entering plasma at 1.1s
Set NINJA for D2 puff at A-B limiter and B016-001. Plenum pressure of 10 PSI.

Shots

Ip= 0.8 MA, NL04 = 0.6
1,2 LSN optimize probe insertion
3,4 USN optimize probe insertion

Ip= 1.1 MA, NL04 = 0.5
5,6 LSN optimize probe insertion
7,8 USN optimize probe insertion

NL04 = 0.8
9,10 USN
11,12 LSN

NL04 = 1.1
13,14 LSN
15,16 USN

NL04 = 1.4
17,18 USN
19,20 LSN

NL04 = 1.7
17,18 USN
19,20 LSN

If time remains...
Change to Bt=4T, Ip= 0.8 MA and continue LSN/USN sequence
NL04 = 0.6

NL04 = 0.4

NL04 = 0.8

NL04 = 1.0

NL04 = 1.2

If Brian is done by 4 PM, we will also try some shots for
MP#429, which aims to get gas puff imaging data for limiter shots to see if
their 'blobs' are any different than those for diverted plasmas.
This will start with repeats of a shot from the previous 1/2 day run
of MP#429.

1050825013: limited discharge, 0.8 MA, 5.4 T, 3.5 cm outer gap,
kappa = 1.2, etc. This old shot disrupted early probably because of the strong GPI gas puff,
which we hope will not be needed this time.

If this goes through we will repeat with various strengths of gas
puff, with and without Brian's probe. If all goes very well we may ask to change the outer gap.


Session Leader Summaries
Entered: Mar 16 2006 06:18:38:143PM
Author: Brian Labombard
Run Summary for 1060316

MP#409 "SOL Phase space studies"
___________________________________________________________________________________
The goal today was to take profile and flow data in 1.1 MA, 5.4 tesla ohmic discharges
in LSN and USN at different densities. In particular, we were looking to see if the
pressure profiles near the separatrix continue to follow an Ip^2 scaling, with
a systematic variation with LSN versus USN.
It was a tough day at the run. First, there was a 2-1/2 hour delay for Jim Irby
to replace the CO2 laser in the TCI system. Second, a problem with cooling an
E-port vertical leg (real or not) slowed the shot cycle way down. After running
a few standard 0.8 MA shots, we managed to get four data points at the new conditions
(1.1 MA, NL04=0.55 & 0.8 in LSN/USN). Unfortunately, the A-port scanning probe
never cleaned up, despite the fact that a new molybdenum head was installed,
just for this MP. On the last shot, we ran an inner-limited discharge for Stewart to
capture turbulence images on the PSI-5 camera.
___________________________________________________________________________________

Quick shot log
Ip=0.8MA, Bt=5.4T
1 - LSN, NL04= 0.8 ASP(+0), FSP(-5) SNE-sweep, W-Vf
2 - LSN, NL04= 0.88 ASP(+7), FSP(+4) SNE-sweep, W-Vf, ISP
3 - LSN, NL04= 0.6 ASP(+9), FSP(+4) SNE-sweep, W-Vf, ISP - target ok
4 - USN, NL04= 0.59 ASP(+3), FSP(-3) SNE-sweep, W-Vf, ISP
5 - USN, NL04= 0.59 ASP(+3), FSP(-3) SNE-sweep, W-Vf, ISP
6 - USN, NL04= 0.59 ASP(+10), FSP(+8) SNE-sweep, W-Vf, ISP - target good

Ip=1.1MA, Bt=5.4T
7 - USN, Ip=1.1MA, NL04= 0.58 ASP(+8), FSP(+6) SNE-sweep, W-Vf, ISP
8 - USN, Ip=1.1MA, NL04= 0.59 ASP(+8), FSP(+4) SNE-sweep, W-Vf, ISP
9 - USN, Ip=1.1MA, NL04= 0.57 ASP(+11), FSP(+4) SNE-sweep, W-Vf, ISP - good targeting, ASP arcing.
10 - LSN, Ip=1.2MA, NL04= 0.52 ASP(+8), FSP(+4) SNE-sweep, W-Vf, ISP
disrupted at 0.85 s
11 - fizzle
12 - LSN, Ip=1.1MA, NL04= 0.53 ASP(+8), FSP(+4) SNE-sweep, W-Vf, ISP
13 - LSN, Ip=1.1MA, NL04= 0.7 ASP(+8), FSP(+4) SNE-sweep, W-Vf, ISP
14 - LSN, Ip=1.1MA, NL04= 0.8 ASP(+8), FSP(+4) SNE-sweep, W-Vf, ISP ASP a bit deep.
15 - fizzle
16 - USN, Ip=1.1MA, NL04= 0.78 ASP(+11), FSP(+4) SNE-sweep, W-Vf, ISP
17 - no power
18 - inner-limited shot

Physics Operator Summaries
Entered: Mar 16 2006 05:04:30:317PM
Author: Ron Parker
Not a great run! It began 2 hours late due to failure of the CO2 laser, which had to be replaced. Then, problems developed with the cooling of the E left outer leg, similar to the problem that we had with the leg at C-port a few weeks ago. Cycle time degraded during the run to 20-25 minutes. Not clear if instrumental but it will have to be examined.

The run still managed to produce some data in both upper and lower null plasmas with the scanning probe. Shots 1-8 ran well, but shots 9 and 10 disrupted, possibly due to interaction with the scanning probe. Shot 11 then fizzled, not surprisingly. Shots 12-14 ran normally, shot 15 fizzled and shot 16 ran OK, the last shot for MP 409. We set up for one shot (limited) for MP 429 and after a no power shot, it ran and produced data.

Scorecard: 13 useful plasma shots, 2 disruptions, 2 fizzles, 1 no power shot.

Session Leader Comments
Mar 16 2006 11:20:51:933AM1060316001Brian LabombardShot 1 LSN, 0.8 MA, NL04=0.8, ASP, FSP scanning at 0.65, 0.85, 1.05 s

Next shot - repeat, with probes deeper.
Mar 16 2006 11:31:43:730AM1060316002Brian LabombardShot 2 LSN, 0.8 MA, NL04=0.87, ASP, FSP scanning at 0.65, 0.85, 1.05 s

Next shot - repeat. Probes need to clean-up.
Mar 16 2006 11:48:49:730AM1060316003Brian LabombardShot 3 LSN, 0.8 MA, NL04=0.6, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s

ASP still is arcing.
Next shot: go to USN
Mar 16 2006 12:42:36:747PM1060316004Brian LabombardShot 4 USN, 0.8 MA, NL04=0.55, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP still is arcing.
ISP over-inserted.
next: repeat
Mar 16 2006 12:57:01:637PM1060316005Brian LabombardShot 5 USN, 0.8 MA, NL04=0.6, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP arcing.

next: repeat with 5 mm decrease of inner gap
Mar 16 2006 01:14:20:543PM1060316006Brian LabombardShot 6 USN, 0.8 MA, NL04=0.6, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP arcing.

next: go to 1.1 MA
Mar 16 2006 01:33:44:277PM1060316007Brian LabombardShot 7 USN, 1.1 MA, NL04=0.6, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP arcing.

next: decrease inner gap by 1mm, decrease outer gap by 4 mm.
Mar 16 2006 01:57:27:043PM1060316008Brian LabombardShot 8 USN, 1.1 MA, NL04=0.55, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP arcing.

next: Repeat with ASP deeper
Mar 16 2006 02:13:13:433PM1060316009Brian LabombardShot 9 USN, 1.1 MA, NL04=0.55, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
ASP arcing.

next: Go to LSN at 1.1MA
Mar 16 2006 04:20:42:927PM1060316010Brian LabombardShot 10 LSN, 1.2 MA, NL04=0.55, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
Disrupted at 0.85 s.

next: Again at 1.1MA
Mar 16 2006 04:21:05:130PM1060316012Brian LabombardShot 12 LSN, 1.1 MA, NL04=0.54, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
data looks ok

next: go to NL04=0.8
Mar 16 2006 04:21:21:677PM1060316013Brian LabombardShot 13 LSN, 1.1 MA, NL04=0.7, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
data looks ok

next: try again for NL04=0.8
Mar 16 2006 04:22:47:097PM1060316014Brian LabombardShot 14 LSN, 1.1 MA, NL04=0.8, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
data looks ok

next: Go to USN with NL04=0.8
Mar 16 2006 04:23:43:490PM1060316016Brian LabombardShot 16 USN, 1.1 MA, NL04=0.8, ASP, FSP, ISP scanning at 0.65, 0.85, 1.05 s
data looks ok

next: Go for inner-limited shot

Physics Operator Comments
Mar 16 2006 09:02:39:310AM1060316001Ron ParkerThe run will get off to a slightly delayed start due to problem with the CO2 laser. It failed last night and is being replaced, but it will take an hour or so to install the new one.
Mar 16 2006 11:41:42:340AM1060316001Bill Rowan001 Plasma

Next shot.
Ne and Ar on for 50 ms
Mar 16 2006 11:25:31:027AM1060316002Bill Rowan002. Plasma
Mar 16 2006 11:36:08:560AM1060316002Bill RowanNext shot.
Decrease nl_04 to 0.6e+20
Mar 16 2006 11:44:27:527AM1060316003Bill Rowan003. Plasma

Next shot.
Switch to segment 3, USN
Changed nl_o4 demaand from 1.0e+20 to 0.6e+20

Mar 16 2006 12:39:09:230PM1060316004Ron ParkerShot 4 ran well, USN. Current was 870 kA, not 800. Offsets were not up to date.
Should be OK for next shot.
Mar 16 2006 12:56:52:170PM1060316005Ron ParkerShot 5 ran well, without offsets (Thanks, Steve)

Next: Reduce inner gap by 5mm. Outer gap no change.
Mar 16 2006 01:15:31:777PM1060316006Ron ParkerShot 6 ran well, Inner gap acceptable.
Next: 1.1 MA. Increase outer gap by 2mm.
Mar 16 2006 01:37:27:873PM1060316007Ron ParkerShot 7 looked good.
Next: tune gaps, 1mm decrease in inner gap, 4 mm decrease in outer gap.
Mar 16 2006 01:51:20:513PM1060316008Ron ParkerShot 8 ran well. Probe did not insert as far on third thrust, so we'll repeat.

Mar 16 2006 02:15:19:323PM1060316009Ron ParkerShot 9 disrupted, possibly due to an event associated with the 2nd probe insertion.

Next: Back to LSN, 1.2 MA. Backporch added to TF.
Mar 16 2006 02:23:58:560PM1060316010Ron ParkerShot 10 disrupted, possibly due to probe insertion. Hard X-rays are a problem.

Try again, requesting 1.1 MA.
Mar 16 2006 02:41:06:683PM1060316011Ron ParkerShot 11 fizzled. We are paying the price for the disruptions.

Try again.
Mar 16 2006 02:55:35:267PM1060316012Ron ParkerShot 12 ran well. Now we'll raise the density to nl_04 =0.8e20.
Mar 16 2006 03:14:57:770PM1060316013Ron ParkerShot 13 ran OK, not quite the density requested. We'll request 8.5e19
Mar 16 2006 03:47:08:143PM1060316014Ron ParkerShot 14 ran OK, next: back to USN with nl_04=0.8e20.

shots are running with > 20 minute cycle time due to slow cooling of E left outer leg.
Mar 16 2006 04:01:57:240PM1060316015Ron ParkerFizzle! Try again.
Mar 16 2006 04:23:12:723PM1060316016Ron ParkerShot 16 ran OK. Last LSN shot. We will now switch to MP#429

Shot will be loaded from 1050825013
Mar 16 2006 04:57:06:177PM1060316017Ron ParkerShot 17 was a no power shot. Try for one more shot.

Engineering Operator Comments
ShotTimeTypeStatusComment
111:06:55:887AMPlasmaOk
211:22:49:937AMPlasmaOk
311:39:30:230AMPlasmaOk
412:26:05:543PMPlasmaOk
512:46:47:497PMPlasmaOk
601:05:50:857PMPlasmaOk
701:24:59:153PMPlasmaOk
801:45:28:200PMPlasmaOk
901:59:36:153PMPlasmaOk
1002:16:46:247PMPlasmaOk
1102:31:45:293PMPlasmaOk
1202:44:22:023PMPlasmaOk
1303:04:56:427PMPlasmaOk
1403:32:25:940PMPlasmaOk
1503:56:50:287PMPlasmaOk
1604:16:43:940PMPlasmaOk
1704:46:27:190PMPlasmaBadI2T fault
1805:00:32:957PMPlasmaOk