Alcator C-Mod Run 1070518 Information

Miniproposals

Miniproposal: 479

Date Filed: 4/27/2007

Title: Effect of Magnetic Shear on Edge Gradients

First Author: Brian Labombard

Session Leader: Brian Labombard (shots 1-30)

Operators
Session leader(s):	Brian Labombard
Physics operator(s):	Ron Parker,Bill Rowan,Ron Parker
Engineering operator(s):	Andy Pfeiffer,Bill Byford

Engineering Operator Run Comment
MP#479 ""Effect of magnetic shear on edge gradients"" SL Brian Labombard

Session Leader Plans

Entered: May 17 2007 02:53:29:540PM

Author: Brian Labombard

Run Plan for 1070518

MP#479 ""Effect of magnetic shear on edge gradients""

Goal
These experiments will investigate the role that magnetic shear may play
in setting the observed pressure gradients near the last-closed flux surface (LCFS)
in ohmic-heated L-mode discharges.

Approach
Vary the magnetic shear at the LCFS by fixing the magnetic topology but varying
the flux surface that defines the LCFS. This is done by first dialing up a double-null
plasma and then systematically reducing the inner wall gap such that the discharge
goes from diverted to inner-wall limited.

Plan
Load from shot#1070511029. This shot ran on segment#4. It was a near-DN discharge
with SSEP control: Ip=0.8 MA, Bt= 5.4 tesla, NL04 = 1.1e20.
Reprogram NL04=0.8e20 and set SSEP to 0.0

ASP, FSP, WASP (for diverted plasmas only) programmed to scan at 0.7, 0.9, 1.1 seconds
GPI viewing lower x-point region.
Edge Thomson scattering with optimized SOL channels.

Shots
Reload #1070511029, turn on segment#4, set SSEP=0.0, NL04=0.8e20

Shots 1-4: Adjust inner gap to 12 mm, outer gap to 15 mm. Optimize scanning probe targets.
Use WASP probe to see if DN balance is attained.

Shots 5-12: NL04 ~ 0.8e20 m-2, scan inner gap: 5, 2, 0, -2, -5, -10 mm
Keep outer gap the same.

Shots 13-20: set NL04 ~ 0.4e20 m-2, can inner gap: 5, 2, 0, -2, -5, -10 mm
Keep outer gap the same.

Shots 21-28: set NL04 ~ 1.2e20 m-2, scan inner gap: 5, 2, 0, -2, -5, -10 mm
Keep outer gap the same.

Physics Operators Plans

Session Leader Summaries

Entered: May 18 2007 09:43:43:700PM

Author: Brian Labombard

Run Summary for 1070518

MP#479 ""Effect of magnetic shear on edge gradients""

This was a very productive run. We ran double-null plasmas all day with varying 'clearin' distances,
causing the discharges to be either diverted with a finite inner wall gap or to be limited onto the
inner wall. In limited discharges, the spacing between the last-closed flux surface and the separatrix
was varied systematically to a maximum of about 12 mm.

We got about 12 shots with a fine clearin scan (~2mm steps) at a nominal density of NL04~0.85 and
with the ASP and FSP probe systems plunging sufficiently deep. The WASP probe was also used to
investigate high-field side profiles in regular double-null plasmas as well as some inner-wall
limited plasmas. (Yes we found that the WASP probe can be used in inner-limited plasmas. We just
don't scan it very far!) The new tungsten electrode geometry, which is now on all the scanning
probes, worked extremely well, surviving some over-insertion errors (Te = 100 eV!) without showing
any damage.

After shot#18, we tried to lower the density to begin the low-density (NL04~0.4) clearin scan part
of the MP. However, these innner-wall limited discharges initially refused to run with densities below
about NL04 ~ 0.6, a phenomenon that we saw earlier during Stewart Zweben's run (MP#428). After
a delay from an OH2U supply problem (shot#22), we did manage to do a coarse clearin scan
at NL04 ~ 0.5. We did not have time to start a high density scan (the MP called for NL04 ~ 1.2).

Before the run, Jerry optimized the placement of the edge Thomson views. He reported that the
ETS system worked well today. His initial analysis of the Thomson data showed that the steep gradient
region essentially followed the location of the LCFS, ignoring the location of the separatrix.
Scanning probe data seems to support this initial conclusion. There may be some differences
in the electron pressure gradient at the LCFS, depending on whether it is limited or
diverted. The Thomson data does not have the spatial resolution to explore this detail.
Therefore, we will need to populate the edge database with probe-profile data to take a close
look at this question. We can't do this immediately because the software needs to be rewritten
to handle the new probe geometries (perpendicular Mach probe) that we are now using.
Stay tuned.

___________________________________________________________________________________
Quick shot log

1- DN, Ip=0.8, Bt=5.6, NL04=0.82-0.7, SP @ 0.68, 0.88, 1.08s, ASP(+5), FSP(+0)
2- DN, Ip=0.8, Bt=5.6, NL04=0.8-0.75, SP @ 0.68, 0.88, 1.08s, ASP(+14), FSP(+6)
3- fizzle
4- early disruption
5- fizzle
6- DN, gap=11mm, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-excellent, FSP(+7)-excellent
7- DN, gap=6mm, Ip=0.8, Bt=5.6, NL04=0.85-0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-could be deeper, FSP(+7)-excellent
8- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.86-0.82, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-excellent
9- DN, gap=0mm, Ip=0.8, Bt=5.6, NL04=0.9, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-could be deeper
10- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.85, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+9)-excellent
11- DN, clearin=-13mm, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+18)-could be deeper, FSP(+11)-ok
12- DN, clearin=-13mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-excelent, FSP(+11)-excellent
13- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-could be deeper, FSP(+13)-could be deeper
14- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+21)-ok, FSP(+14)-ok
15- DN, clearin=-17mm, NL04=0.8-0.84, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-ok, FSP(+17)-excellent
16- DN, clearin=-19mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+19)-excellent
17- DN, clearin=-21mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+20)-excellent
18- DN, clearin=-23mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-first scan good, FSP(+21)-good
19- DN, clearin=-23mm, NL04=0.75-0.8, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-first scan ok, FSP(+20)-could be deeper
20- DN, clearin=-23mm, NL04=0.65-0.72, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-could be deeper, FSP(+24)-great
21- DN, clearin=-23mm, NL04=0.7, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+28)-ok, FSP(+24)-ok
22- OH2U power supply problem, DBN fires an heats inner wall
23- disrupts at 1 second, DN, clearin=-19mm, NL04=0.46, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+25)-ok, FSP(+20)-ok
24- fizzle
25- disrupts 0.7s
26- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.5, no probes scanning
27- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.67-0.5, SP @ 0.75, 0.95, 1.15s, ASP(+18)-ok, FSP(+9)-ok
28- DN, clearin=-19mm, NL04=0.68-0.63, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+23)-could be deeper , FSP(+20)-could be deeper
29- DN, clearin=-19mm, NL04=0.68-0.65, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-ok , FSP(+22)-ok
30- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.52-0.42, SP @ 0.75, 0.95, 1.15s, ASP(+19)-excellent, FSP(+8)-excellent

Physics Operator Summaries

Entered: May 18 2007 05:31:28:840PM

Author: Ron Parker

Run was devoted to MP#479 "Effect of magnetic shear on edge gradients" with B. LaBombard as Session Leader. Brian required a systematic scan of the inner gap at two densities for this run. We scanned Clearin from +3mm to -23 mm (strongly inner wall limited) at nl_04 ~ 8.0e19 m-2, then back out to -6 mm with nl_04 ~ 6e19 m-2 (not as low as Brian wanted, but it was what the machine gave us.) The outward scan was courser than the inward one.

Late in the run, Steve reported that an EF power supply was railed for most if not all the shots, and it is interesting that the shots nevertheless went off fairly well.

There were more fizzles and disruptions than one would have liked, some of which were at least partially due to the beam firing without plasma. Brian believes that this results in loosely bound material on the inner wall, where the beam strikes it, and this material is easily knocked off particularly by inner wall limited plasmas.

There was also one machine failure due to a loose connection in the power supply circuitry. This was easily fixed and did not result in a serious delay.

Scorecard: 30 plasma attempts, 23 full length (at least well into rampdown), 3 fizzles (2 after disruptions), 3 disruptions and 1 commutation failure.

Session Leader Comments

May 18 2007 09:10:48:833AM 1070518001 Brian Labombard 1- DN, Ip=0.8, Bt=5.6, NL04=0.82-0.7, SP @ 0.68, 0.88, 1.08s, ASP(+5), FSP(+0)

Next: repeat with probes deeper and add WASP

May 18 2007 09:30:59:013AM 1070518002 Brian Labombard 2- DN, Ip=0.8, Bt=5.6, NL04=0.8-0.75, SP @ 0.68, 0.88, 1.08s, ASP(+14), FSP(+6)

Next: repeat, probes deeper

May 18 2007 10:30:55:287AM 1070518006 Brian Labombard 6- DN, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-excellent, FSP(+7)-excellent

Next: go to inner gap = 5mm, keeping outer gap fixed.

May 18 2007 10:45:01:073AM 1070518007 Brian Labombard 7- DN, gap=6mm, Ip=0.8, Bt=5.6, NL04=0.85-0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-could be deeper, FSP(+7)-excellent

Next: go to inner gap = 2mm, keeping outer gap fixed.

May 18 2007 10:59:06:267AM 1070518008 Brian Labombard 8- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.86-0.82, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-excellent

Next: go to inner gap = 0, keeping outer gap fixed.

May 18 2007 11:13:40:490AM 1070518009 Brian Labombard 9- DN, gap=0mm, Ip=0.8, Bt=5.6, NL04=0.9, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-could be deeper

Next: go to inner gap = ""-2mm"", keeping outer gap fixed.

May 18 2007 11:29:09:137AM 1070518010 Brian Labombard 10- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.85, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+9)-excellent
Inner wall contact with this setting of clearin.

Next: clearin at -13mm, keeping outer gap fixed.

May 18 2007 11:49:35:630AM 1070518011 Brian Labombard 11- DN, clearin=-13mm, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+18)-could be deeper, FSP(+11)-ok

Next: repeat

May 18 2007 12:58:38:033PM 1070518012 Brian Labombard 12- DN, clearin=-13mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-excelent, FSP(+11)-excellent

Next: go to clearin = -15mm

May 18 2007 12:59:35:750PM 1070518013 Brian Labombard 13- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-could be deeper, FSP(+13)-could be deeper

Next: repeat

May 18 2007 01:32:42:107PM 1070518014 Brian Labombard 14- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+21)-ok, FSP(+14)-ok

Next: go to clearin=-17mm

May 18 2007 01:00:20:720PM 1070518015 Brian Labombard 15- DN, clearin=-17mm, NL04=0.8-0.84, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-ok, FSP(+17)-excellent

Next: go to clearin=-19mm

May 18 2007 12:57:49:750PM 1070518016 Brian Labombard 16- DN, clearin=-19mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+19)-excellent

Next: go to clearin=-21mm

May 18 2007 01:14:24:367PM 1070518017 Brian Labombard 17- DN, clearin=-21mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+20)-excellent

Next: go to clearin=-23mm

May 18 2007 01:31:56:500PM 1070518018 Brian Labombard 18- DN, clearin=-23mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-first scan good, FSP(+21)-good

Next: go to NL04=0.4

May 18 2007 01:39:06:220PM 1070518019 Brian Labombard 19- DN, clearin=-23mm, NL04=0.75-0.8, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-first scan ok, FSP(+20)-could be deeper

Next: repeat

May 18 2007 01:56:41:100PM 1070518020 Brian Labombard 20- DN, clearin=-23mm, NL04=0.65-0.72, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-could be deeper, FSP(+24)-great

Next: repeat

May 18 2007 02:09:16:200PM 1070518021 Brian Labombard 21- DN, clearin=-23mm, NL04=0.7, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+28)-ok, FSP(+24)-ok

Next: clearin=-19mm

May 18 2007 03:53:28:160PM 1070518023 Brian Labombard 23- DN, clearin=-19mm, NL04=0.46, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+25)-ok, FSP(+20)-ok
=> disrupts at 1 second. Junk comes off inner wall, probably because DNB heated wall on previous no-plasma shot.

Next: repeat

May 18 2007 04:09:59:810PM 1070518025 Brian Labombard 25 => disrupts at 0.7 s. Junk is still coming off inner wall.

Next: reload shot#10

May 18 2007 04:19:38:563PM 1070518026 Brian Labombard 26- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.5, no probes scanning

Next: repeat with probes

May 18 2007 04:54:09:200PM 1070518027 Brian Labombard 27- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.67-0.5, SP @ 0.75, 0.95, 1.15s, ASP(+18)-ok, FSP(+9)-ok

Next: reload shot#16 with NL04=0.5

May 18 2007 04:43:43:760PM 1070518028 Brian Labombard 28- DN, clearin=-19mm, NL04=0.68-0.63, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+23)-could be deeper , FSP(+20)-could be deeper

Next: repeat with probes deeper

May 18 2007 05:01:36:283PM 1070518029 Brian Labombard 29- DN, clearin=-19mm, NL04=0.68-0.65, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-ok , FSP(+22)-ok

Next: reload shot#8 with NL04=0.5

May 18 2007 05:24:29:383PM 1070518030 Brian Labombard 30- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.52, SP @ 0.75, 0.95, 1.15s, ASP(+19)-excellent, FSP(+8)-excellent

Physics Operator Comments

May 17 2007 05:35:50:577PM Ron Parker Engineering Setup
------------------

Overnight ECDC in D2, p_fill = 2e-4

Run begins at 09:00 (lock-up at 08:30) and ends at 17:00

Power systems as on 1070511029

Acoil: +Dtop -Dbot -Jtop +Jbot (standard) Hybrid Enabled

Gas setup:
---------
fill B-Top with 6 psi D2 : Hybrid enabled (PG4)
fill B-side lower with 1 psi Ar : Hybrid DISABLED (PG1)
leave B-side upper as is : Hybrid DISABLED (PG2)
fill B-main (C-side) with 40 psi D2 : Hybrid enabled (PG3)
pump out NINJA and backfill with 10 PSI of D2, then enable.

Enable the following gate valves and shutters:
ECE, VUV, Z-bolo shutters

Torvac setup: Pumpstack gatevalves OPEN
RGAs on

ICRF: {Steve Wukitch - please specify}

LH: None

Run Plan:

See Session Leader Plan for shot sequence.

May 18 2007 09:03:09:813AM 1070518001 Ron Parker Good morning. Machine ready to go. Shot 1070511029 loaded with the following mods:
B_T =5.6 T, nl_04=8e19 m-2, ssep = 0.

May 18 2007 09:32:30:123AM 1070518001 Ron Parker Shot 1 ran well, probably will be the best of the day.

May 18 2007 09:34:53:530AM 1070518002 Ron Parker Shot 2 ran OK. More or less the same as shot 1.

May 18 2007 09:39:10:377AM 1070518003 Ron Parker Shot 3 fizzled. Early breakdown but burnout is slow.

No changes for next shot, see if it goes.

May 18 2007 09:57:09:117AM 1070518004 Ron Parker Shot 4 disrupted early, 0.18 s. Too much gas.

Try again.

May 18 2007 10:03:14:667AM 1070518005 Ron Parker Shot fizzled, not surprising after disruption on previous shot.

May 18 2007 10:07:50:810AM 1070518005 Ron Parker For next shot, reduce BR(0) from 0.0038 to 0.0030

May 18 2007 10:29:17:083AM 1070518006 Ron Parker Shot 6 ran OK. JT finds Halpha filter had fallen off, explaining large Halpha signals.

Next: Reduce inner gap from 11 to 5 mm, keeping outer gap the same by reducing Rcur by 3 mm.

May 18 2007 10:48:16:480AM 1070518007 Ron Parker Shot 7 ran OK. Next: Reduce inner gap by 3 mm, Rcur by 1.5 to keep outer gap constant.

May 18 2007 10:59:25:437AM 1070518008 Ron Parker Shot 8 looked good. Next: Reduce clearin by 3 mm, Rcur by 1.5.

May 18 2007 11:14:20:663AM 1070518009 Ron Parker Shot 9 ran. Next: Reduce clearin by 2 mm, Rcur by 1.

May 18 2007 11:25:51:980AM 1070518010 Ron Parker Shot 10 ran OK. Next: Clearin reduced by 2mm, from -11 to -13 mm and Rcur by 1 mm from 652 to 651 mm.

May 18 2007 11:47:25:827AM 1070518011 Ron Parker Shot 11 ran well, repeat for next shot.

May 18 2007 11:55:22:213AM 1070518012 Ron Parker Shot 12 ran well. Reduce Clearin again by 2 mm, from -13 mm to -15 mm and Rcur by 1, from 651 to 650.

May 18 2007 12:08:39:560PM 1070518013 Ron Parker Shot 13 ran OK, disrupting on current rampdown around 200 kA. Repeat for next shot.

May 18 2007 12:25:03:880PM 1070518014 Ron Parker Shots are rolling along. Next: Reduce Clearin by 2 more mm, from -15 to -17 mm, and Rcur by 1,from 650 to 649 mm.

May 18 2007 12:41:12:697PM 1070518015 Ron Parker Shot 15 looked good. Next: Brian is relentless - reduce Clearin by 2 more mm for next shot.

Reduce Clearin by 2mm, from -17 to -19 mm, but this time leave Rcur at 649 (since the outer gap seems to be growing).

May 18 2007 12:54:24:517PM 1070518016 Ron Parker Shot 16 ran well. Next: Continue Clearin scan inward. Reduce Clearin from -19 to -21, no change for Rcur.

May 18 2007 01:25:00:057PM 1070518017 Ron Parker Shot 17 was OK, although startup was a bit dicey.

For shot 18, reduce Clearin by 2 more mm, from -21 to -23 mm. Again, no change for Rcur

May 18 2007 01:25:34:403PM 1070518018 Ron Parker Shot 18 ran well, startup better than shot 17, but no change was made.

Next: same gaps, nl_04 reduced to 4e19.

May 18 2007 01:34:01:530PM 1070518019 Ron Parker 019. Plasma. Shot was OK

May 18 2007 01:47:10:287PM 1070518020 Ron Parker 020. Plasma. The goal is nl_04=0.4e+20. nl_04 is actually 0.7e+20

May 18 2007 02:00:17:040PM 1070518021 Ron Parker 021. Plasma. nl_04=0.7e+20

May 18 2007 02:20:33:800PM 1070518021 Ron Parker Next shot: Returning to approximately the setup of shot 016. The only change is that CLEARIN is changed to -0.019 for this shot.

After shot 021, there was a "bang". The concensus was that this came from the power room. An inspection revealed nothing.

May 18 2007 02:23:00:220PM 1070518022 Ron Parker 022. Power supply problems. OH2U

May 18 2007 02:39:29:070PM 1070518022 Ron Parker 022. Power supply problems. OH2U

Problem has been diagnosed and traced to a broken connection in the commutation network.

Short delay while problem is fixed.

May 18 2007 03:43:03:173PM 1070518023 Ron Parker Shot 23 was ugly -- started up but disrupted just after 1 s.

Steve reports that EF power supply is railing during the shot --but it ran all day like this?!

May 18 2007 03:47:47:487PM 1070518024 Ron Parker Shot 24 fizzled, not surprising after disruption on 23.

Beam is giving some problems due to firing without plasma. Beam valve disabled in order to try to finish run plan.

May 18 2007 04:09:26:747PM 1070518025 Ron Parker Shot 25 disrupted at ~ 700 ms.

May 18 2007 04:29:14:363PM 1070518026 Ron Parker Shot 26 ran well, Brian's probes were not set properly for this shot and we'll repeat.

May 18 2007 04:30:49:740PM 1070518027 Ron Parker Shot 27 ran, we'll move the Clearin out to -19, similar to shot 16 but with lower density.

May 18 2007 04:56:09:077PM 1070518028 Ron Parker Decent shot, a bit bumpy current rise but usable. Probes weren't deep enough so we'll repeat.

May 18 2007 04:53:56:967PM 1070518029 Ron Parker Shot 29 ran OK, not a pretty startup but flattop OK. Next and final shot: Repeat of shot 8 with lower density.

May 18 2007 05:10:29:847PM 1070518030 Ron Parker Shot 30 was OK, disrupted on ramp down @ ~ 500 kA.

Engineering Operator Comments

Shot Time Type Status Comment

1 09:03:29:080AM Plasma Ok

2 09:17:18:023AM Plasma Ok

3 09:29:54:763AM Plasma Ok

4 09:42:46:767AM Plasma Ok

5 09:59:43:557AM Plasma Ok

6 10:12:15:857AM Plasma Ok

7 10:34:44:507AM Plasma Ok

8 10:49:08:170AM Plasma Ok

9 11:02:02:783AM Plasma Ok

10 11:16:11:570AM Plasma Ok

11 11:35:00:593AM Plasma Ok

12 11:47:56:337AM Plasma Ok

13 12:01:45:870PM Plasma Ok

14 12:14:43:327PM Plasma Ok

15 12:29:59:960PM Plasma Ok

16 12:42:56:667PM Plasma Ok

17 12:57:07:093PM Plasma Ok

18 01:11:30:320PM Plasma Ok

19 01:29:58:060PM Plasma Ok

20 01:43:52:363PM Plasma Ok

21 01:56:52:180PM Plasma Ok

22 02:17:33:377PM Plasma Bad OH2U comm flt

23 03:27:27:887PM Plasma Ok

24 03:43:15:750PM Plasma Ok

25 03:58:03:710PM Plasma Ok

26 04:10:59:030PM Plasma Ok

27 04:23:58:970PM Plasma Ok

28 04:36:43:430PM Plasma Ok

29 04:49:51:950PM Plasma Ok

30 05:02:54:470PM Plasma Ok

System Availability

May 18 2007 09:03:06:317AM

System Available Comment Availability
Changed Owner Description Who Can
Change
Active MHD yes Fully operational Mar 28 2007 09:19PM (sears) Joe Snipes Active MHD Antenna sears,snipes
BES yes vertical array of six views at R ~ 87.3 cm, radial array of three views out to R ~ 89 cm, both at outboard midplane. Three discrete fiber views of beam at R ~ 70.0, 76.5 and 82.5 cm. Feb 06 2007 10:00AM (bravenec) Ron Bravenec Beam Emission Spectroscopy bravenec
Bolometers yes 2Pi diode operational, 2Pi foil being upgrade for noise resistance. Midplane foils being digitized but not calibrated, still ICRF pickup. Midplane AXUV and divertor being digitized but analyzed data not ready. Apr 26 2007 10:27AM (mlreinke) Matt Reinke Bolometers hutch,mlreinke
Boronization yes First Boronization 5/9/07 May 10 2007 04:55PM (irby) Jim Irby Boronization dekow,irby
CNPA no Jan 14 2007 02:06PM Ron Parker Compact Neutral Analyzer parker
Cryopump - Upper Divertor no In-vessel hardware is installed; in-vessel cryogenic systems are leak-tight and have passed LN2 cool-down tests. Work is proceeding on external LHe and LN2 transfer lines as well as PLC control system. Mar 30 2007 10:53AM (labombard) Brian LaBombard Upper Divertor Cryopump irby,labombard
CXRS yes The pedestal toroidal array was installed, spatially and absolutely calibrated. There are 10 chords intersect the beam at the major_R_range=[75,4:87.4]cm. Spatial resolution: 1.2 cm. The F-top poloidal array was installed and spatially calibrated. There are 19 chords intersect the beam at the major_R_range=[67.8:91.0]cm. Spatial resolution: 1.22 cm. May 01 2007 12:31PM (bespam) Bill Rowan Charge Exchange Spectroscopy bespam,blip,rachmcd,rowan
D Alpha yes \ha2_bright and \SPECTROSCOPY::TOP.VUV.VIS_SIGNALS:MCP_VIS_SIG1 are available Mar 11 2007 10:28PM (terry) Jim Terry Balmer Alpha Monitor irby,terry,wolfe
Dalsa yes camera is re-installed, and view has been calibrated Feb 26 2007 03:28PM (marmar) Earl Marmar Visible Bremsstrahlung marmar
Disruption Mitigation no Jan 14 2007 02:02PM Bob Granetz Gas Jet granetz,whyte
Divertor IR no Mar 06 2007 10:50AM Glen Wurden Divertor IR Digital Video gwurden,terry
Divertor IR Spectroscopy no Mar 06 2007 10:51AM Glen Wurden Divertor IR Spectroscopy gwurden,ldorf,terry
DNB yes All systems are operational, but as of 28 March 2007, the beam needs additional conditioning for full performance shots Mar 28 2007 09:36AM (beals) Bob Granetz Diagnostic Beam beals,granetz
FRC-ECE yes All channels now working. Apr 04 2007 11:04AM (phillips) Perry Phillips Heterodyne ECE-32 channels phillips
G-Side Ratiomatic yes The gauge is operational. Mar 30 2007 10:54AM (labombard) Brian LaBombard G-side ratiomatic ionization gauge labombard,toland
GPC yes Chs 1-8 operational. But, low and noisy signals on SOME shots, others OK. May 10 2007 10:01AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPC2 yes Most slow channels (except 1,8,10,17) operational. Set to lower freqs for LHCD. Apr 11 2007 09:34AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPI yes New view just outside of the lower X-point is operational, but data is being archived locally , not to the tree. Midplane GPI is not operational. Mar 27 2007 01:59PM (terry) Jim Terry Gas Puff Imaging terry,zweben
H/D yes spectral calibration needs to be checked, but system should be ready for the run Feb 26 2007 03:28PM (marmar) Earl Marmar H/D Ratio marmar
Hirex Jr yes Mar 06 2007 08:59AM (rice) John Rice High Resolution X-Ray ince,rice
Hirex Sr yes Storing Data, but profiles not yet available Apr 27 2007 01:20PM (ince) John Rice High Resolution X-Ray ince,rice
HXR yes Something might be wrong with channel 26; all others working fine. Mar 23 2007 10:43AM (schmidt) Ron Parker Hard X-Ray Array parker,schmidt
ICRF D-Antenna yes 80.5 MHz. ready Mar 28 2007 08:50AM (ylin) Steve Wukitch D-port antenna wukitch,ylin
ICRF E-Antenna no 80 MHz. FFT installation/coaxial line needs more work Mar 16 2007 09:32AM (ylin) Steve Wukitch E-port antenna wukitch,ylin
ICRF J-Antenna yes 78 MHz Apr 04 2007 08:56AM (ylin) Steve Wukitch J-port antenna wukitch,ylin
Lower Hybrid no 6B Pressure window failed. Arcing in 6B, 8B,9B & 23B. May 04 2007 03:44PM (dterry) Ron Parker Lower Hybrid dterry,parker
LPI yes Apr 26 2007 08:35PM (bose) Earl Marmar Lithium Pellet Injector bose,marmar
Ly-alpha yes Midplane data being digitized, but analyzed data not ready. 2D arrays being debugged. Apr 26 2007 10:28AM (mlreinke) Matt Reinke Lyman alpha cameras labombard,mlreinke
McPherson yes Working normally. Apr 19 2007 09:52AM (mlreinke) Jim Terry VUV Spectrometer mlreinke,terry
Michelson yes Operational. Mar 28 2007 08:33AM (hubbard) Amanda Hubbard ECE Te Profiles hubbard,schmidt
MKS yes E-Top, E-Bottom, F-top (cryo), G-side, and B-bottom are operational. F-top gauge has a 'sniffer tube' to measure pressures in cryopump gas box. Mar 20 2007 06:42PM (g) Brian LaBombard Baratron pressure gauges labombard
MLP no Bench tests are proceeding on a prototype MLP system. We hope to roll the system into the cell for testing in a few weeks, powering up a single electrode on the A-port scanning probe. Mar 13 2007 09:57PM (labombard) Brian LaBombard Mirror Langmuir Probe Electronics System labombard
MSE no (1) Bandpass filters replacement underway (2) Beam-into-gas spectrum measurement underway (3) Shutter mechanism currently unstable; remains open. (4) Expect beam-into-gas calibrations complete about 4/24. Apr 03 2007 12:05PM (sscott) Steve Scott Motional Stark Effect jinseok,sscott
Neutrons yes Both neutron systems are fully operational Apr 05 2007 11:19AM (fiore) Catherine Fiore Neutron Detectors fiore
Neuts and Hards yes operational Mar 21 2007 04:29PM (irby) Jim Irby X-Ray/Neutron Detector at K-Hor irby
NINJA yes All capillaries displayed by the NINJA_CONTROL GUI have been tested. NINJA puffed on 1070329009 (A-B limiter). Mar 29 2007 11:47AM (terry) Brian LaBombard NINJA gas puff labombard,terry
PCI no System unavailable. The laser is under repair. Apr 04 2007 11:16PM (lianglin) Miklos Porkolab Phase Contrast Imaging edlund,lianglin,ntsujii,porkolab
Penning Gauges yes 8 in-situ Penning ionization gauges appear to be operational: CB_DivU, CB_OutL, CB_DivL, KA_OutU, KA_OutL, B_DivL, Cryo_1, Cryo_2. Cryo_1 and Cryo_2 are new and installed in the upper cryopump 'gas-box'. Mar 13 2007 10:01PM (labombard) Brian LaBombard Penning Ionization Gauges labombard
Plasma TV yes WIDE1, WIDE2 (chan 33), DANT, JANT and DIV (without an ND filter) are operational. Mar 27 2007 01:53PM (terry) Jim Terry Video of plasma via several cameras dekow,irby,terry,wolfe
Polarimeter no Retro shutter closed Mar 15 2007 11:00AM (irby) Jim Irby C-Mod Polarimeter irby
Probe Array - ISD yes Probes at 15 of the 16 poloidal locations ('ramped' geometry) are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:47PM (labombard) Brian Labombard Inner Lower Divertor Probe Array labombard
Probe Array - LH yes All 6 probes on the lower hybrid launcher (tungsten, 1.5 mm projection) are operational. Mar 13 2007 09:46PM (labombard) Brian LaBombard Lower Hybrid Probe Array labombard
Probe Array - OSD yes Probes at 10 poloidal locations (one 'ramped' and one 'flush') are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:45PM (labombard) Brian LaBombard Outer Lower Divertor Probe Array labombard
Probe Array - UDIV yes 14 probes are operational ('ramped' geometry). n,Te, particle flux reported every 10 ms.Two high-gain channels are installed and operational for ECDC plasma diagnosis. Mar 13 2007 12:46PM (labombard) Brian LaBombard Upper Divertor Probe Array labombard
Reflectometer yes The 60 and 110 are connected but still being tested. The Swept frequency channel is sweeping with the waveform voltage swept at 2Hz with the voltage 176mV-1176mV (100.8GHz-105.2GHz), also in the testing stage. May 17 2007 11:15PM (dominguez) Earl Marmar Reflectometer dominguez,marmar
Scanning Probe - ASP yes Perpendicular Mach probe head is installed. The drive is operational. Mar 15 2007 09:09PM (labombard) Brian LaBombard A-Port Scanning Probe labombard
Scanning Probe - FSP yes Perpendicular Mach probe head is installed. The probe drive is now operational. Mar 13 2007 09:51PM (labombard) Brian LaBombard F-Port Scanning Probe labombard
Scanning Probe - WASP yes A-port WASP successfully collected data on 04/04. Some intermittent open circuit on SE Electrode. K-WASP took data on 04/11. Both ready to scan as needed. Apr 12 2007 04:18PM (nsmick) Brian LaBombard Inner Wall Scanning Probe labombard,nsmick
TCI yes NL04 at 71.04 cm from 3/9/07 calibration Mar 09 2007 05:47PM (irby) Jim Irby Two-Color Interferometer (TCI) irby,murray
TS - Core yes 2 lasers, 11 spatial channels. Density is calibrated based on ECE cutoffs obtained on 4 May 2007. Additional spatial channels will be added over the next several weeks. May 10 2007 10:37AM (jwhughes) Jerry Hughes Core Thomson scattering jwhughes
TS - Edge yes 2 lasers, 20 spatial channels. Density is cross-calibrated to the core system, based on shots 1070504014, 016, and 019. May 17 2007 09:14AM (jwhughes) Jerry Hughes Millimeter resolution edge Thomson scattering jwhughes
Vispec yes 350 and 670 nm, 4 spatial channels May 04 2007 01:02PM (agraf) Alex Graf Visible Spectrometer agraf

May 18 2007 11:15:46:537AM

System Available Comment Availability
Changed Owner Description Who Can
Change
Active MHD yes Fully operational Mar 28 2007 09:19PM (sears) Joe Snipes Active MHD Antenna sears,snipes
BES yes vertical array of six views at R ~ 87.3 cm, radial array of three views out to R ~ 89 cm, both at outboard midplane. Three discrete fiber views of beam at R ~ 70.0, 76.5 and 82.5 cm. Feb 06 2007 10:00AM (bravenec) Ron Bravenec Beam Emission Spectroscopy bravenec
Bolometers yes 2Pi diode operational, 2Pi foil being upgrade for noise resistance. Midplane foils being digitized but not calibrated, still ICRF pickup. Midplane AXUV and divertor being digitized but analyzed data not ready. Apr 26 2007 10:27AM (mlreinke) Matt Reinke Bolometers hutch,mlreinke
Boronization yes First Boronization 5/9/07 May 10 2007 04:55PM (irby) Jim Irby Boronization dekow,irby
CNPA no Jan 14 2007 02:06PM Ron Parker Compact Neutral Analyzer parker
Cryopump - Upper Divertor no In-vessel hardware is installed; in-vessel cryogenic systems are leak-tight and have passed LN2 cool-down tests. Work is proceeding on external LHe and LN2 transfer lines as well as PLC control system. Mar 30 2007 10:53AM (labombard) Brian LaBombard Upper Divertor Cryopump irby,labombard
CXRS yes The pedestal toroidal array was installed, spatially and absolutely calibrated. There are 10 chords intersect the beam at the major_R_range=[75,4:87.4]cm. Spatial resolution: 1.2 cm. The F-top poloidal array was installed and spatially calibrated. There are 19 chords intersect the beam at the major_R_range=[67.8:91.0]cm. Spatial resolution: 1.22 cm. May 01 2007 12:31PM (bespam) Bill Rowan Charge Exchange Spectroscopy bespam,blip,rachmcd,rowan
D Alpha yes \ha2_bright and \SPECTROSCOPY::TOP.VUV.VIS_SIGNALS:MCP_VIS_SIG1 are available Mar 11 2007 10:28PM (terry) Jim Terry Balmer Alpha Monitor irby,terry,wolfe
Dalsa yes camera is re-installed, and view has been calibrated Feb 26 2007 03:28PM (marmar) Earl Marmar Visible Bremsstrahlung marmar
Disruption Mitigation no Jan 14 2007 02:02PM Bob Granetz Gas Jet granetz,whyte
Divertor IR no Mar 06 2007 10:50AM Glen Wurden Divertor IR Digital Video gwurden,terry
Divertor IR Spectroscopy no Mar 06 2007 10:51AM Glen Wurden Divertor IR Spectroscopy gwurden,ldorf,terry
DNB yes All systems are operational, but as of 28 March 2007, the beam needs additional conditioning for full performance shots Mar 28 2007 09:36AM (beals) Bob Granetz Diagnostic Beam beals,granetz
FRC-ECE yes All channels now working. Apr 04 2007 11:04AM (phillips) Perry Phillips Heterodyne ECE-32 channels phillips
G-Side Ratiomatic yes The gauge is operational. Mar 30 2007 10:54AM (labombard) Brian LaBombard G-side ratiomatic ionization gauge labombard,toland
GPC yes Chs 1-8 operational. But, low and noisy signals on SOME shots, others OK. May 10 2007 10:01AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPC2 yes Most slow channels (except 1,8,10,17) operational. Set to lower freqs for LHCD. Apr 11 2007 09:34AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPI yes New view just outside of the lower X-point is operational, but data is being archived locally , not to the tree. Midplane GPI is not operational. Mar 27 2007 01:59PM (terry) Jim Terry Gas Puff Imaging terry,zweben
H/D yes spectral calibration needs to be checked, but system should be ready for the run Feb 26 2007 03:28PM (marmar) Earl Marmar H/D Ratio marmar
Hirex Jr yes Mar 06 2007 08:59AM (rice) John Rice High Resolution X-Ray ince,rice
Hirex Sr yes Storing Data, but profiles not yet available Apr 27 2007 01:20PM (ince) John Rice High Resolution X-Ray ince,rice
HXR yes Something might be wrong with channel 26; all others working fine. Mar 23 2007 10:43AM (schmidt) Ron Parker Hard X-Ray Array parker,schmidt
ICRF D-Antenna yes 80.5 MHz. ready Mar 28 2007 08:50AM (ylin) Steve Wukitch D-port antenna wukitch,ylin
ICRF E-Antenna no 80 MHz. FFT installation/coaxial line needs more work Mar 16 2007 09:32AM (ylin) Steve Wukitch E-port antenna wukitch,ylin
ICRF J-Antenna yes 78 MHz Apr 04 2007 08:56AM (ylin) Steve Wukitch J-port antenna wukitch,ylin
Lower Hybrid no 6B Pressure window failed. Arcing in 6B, 8B,9B & 23B. May 04 2007 03:44PM (dterry) Ron Parker Lower Hybrid dterry,parker
LPI yes Apr 26 2007 08:35PM (bose) Earl Marmar Lithium Pellet Injector bose,marmar
Ly-alpha yes Midplane data being digitized, but analyzed data not ready. 2D arrays being debugged. Apr 26 2007 10:28AM (mlreinke) Matt Reinke Lyman alpha cameras labombard,mlreinke
McPherson yes Working normally. Apr 19 2007 09:52AM (mlreinke) Jim Terry VUV Spectrometer mlreinke,terry
Michelson yes Operational. Mar 28 2007 08:33AM (hubbard) Amanda Hubbard ECE Te Profiles hubbard,schmidt
MKS yes E-Top, E-Bottom, F-top (cryo), G-side, and B-bottom are operational. F-top gauge has a 'sniffer tube' to measure pressures in cryopump gas box. Mar 20 2007 06:42PM (g) Brian LaBombard Baratron pressure gauges labombard
MLP no Bench tests are proceeding on a prototype MLP system. We hope to roll the system into the cell for testing in a few weeks, powering up a single electrode on the A-port scanning probe. Mar 13 2007 09:57PM (labombard) Brian LaBombard Mirror Langmuir Probe Electronics System labombard
MSE no (1) Bandpass filters replacement underway (2) Beam-into-gas spectrum measurement underway (3) Shutter mechanism currently unstable; remains open. (4) Expect beam-into-gas calibrations complete about 4/24. Apr 03 2007 12:05PM (sscott) Steve Scott Motional Stark Effect jinseok,sscott
Neutrons yes Both neutron systems are fully operational Apr 05 2007 11:19AM (fiore) Catherine Fiore Neutron Detectors fiore
Neuts and Hards yes operational Mar 21 2007 04:29PM (irby) Jim Irby X-Ray/Neutron Detector at K-Hor irby
NINJA yes All capillaries displayed by the NINJA_CONTROL GUI have been tested. NINJA puffed on 1070329009 (A-B limiter). Mar 29 2007 11:47AM (terry) Brian LaBombard NINJA gas puff labombard,terry
PCI no System unavailable. The laser is under repair. Apr 04 2007 11:16PM (lianglin) Miklos Porkolab Phase Contrast Imaging edlund,lianglin,ntsujii,porkolab
Penning Gauges yes 8 in-situ Penning ionization gauges appear to be operational: CB_DivU, CB_OutL, CB_DivL, KA_OutU, KA_OutL, B_DivL, Cryo_1, Cryo_2. Cryo_1 and Cryo_2 are new and installed in the upper cryopump 'gas-box'. Mar 13 2007 10:01PM (labombard) Brian LaBombard Penning Ionization Gauges labombard
Plasma TV yes WIDE1, WIDE2 (chan 33), DANT, JANT and DIV (without an ND filter) are operational. Mar 27 2007 01:53PM (terry) Jim Terry Video of plasma via several cameras dekow,irby,terry,wolfe
Polarimeter no Retro shutter closed Mar 15 2007 11:00AM (irby) Jim Irby C-Mod Polarimeter irby
Probe Array - ISD yes Probes at 15 of the 16 poloidal locations ('ramped' geometry) are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:47PM (labombard) Brian Labombard Inner Lower Divertor Probe Array labombard
Probe Array - LH yes All 6 probes on the lower hybrid launcher (tungsten, 1.5 mm projection) are operational. Mar 13 2007 09:46PM (labombard) Brian LaBombard Lower Hybrid Probe Array labombard
Probe Array - OSD yes Probes at 10 poloidal locations (one 'ramped' and one 'flush') are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:45PM (labombard) Brian LaBombard Outer Lower Divertor Probe Array labombard
Probe Array - UDIV yes 14 probes are operational ('ramped' geometry). n,Te, particle flux reported every 10 ms.Two high-gain channels are installed and operational for ECDC plasma diagnosis. Mar 13 2007 12:46PM (labombard) Brian LaBombard Upper Divertor Probe Array labombard
Reflectometer yes The 60 and 110 are connected but still being tested. The Swept frequency channel is sweeping with the waveform voltage swept at 5Hz with the voltage 4.5V-7.5V (120GHz-133.3GHz), also in the testing stage. May 18 2007 11:12AM (dominguez) Earl Marmar Reflectometer dominguez,marmar
Scanning Probe - ASP yes Perpendicular Mach probe head is installed. The drive is operational. Mar 15 2007 09:09PM (labombard) Brian LaBombard A-Port Scanning Probe labombard
Scanning Probe - FSP yes Perpendicular Mach probe head is installed. The probe drive is now operational. Mar 13 2007 09:51PM (labombard) Brian LaBombard F-Port Scanning Probe labombard
Scanning Probe - WASP yes A-port WASP successfully collected data on 04/04. Some intermittent open circuit on SE Electrode. K-WASP took data on 04/11. Both ready to scan as needed. Apr 12 2007 04:18PM (nsmick) Brian LaBombard Inner Wall Scanning Probe labombard,nsmick
TCI yes NL04 at 71.04 cm from 3/9/07 calibration Mar 09 2007 05:47PM (irby) Jim Irby Two-Color Interferometer (TCI) irby,murray
TS - Core yes 2 lasers, 11 spatial channels. Density is calibrated based on ECE cutoffs obtained on 4 May 2007. Additional spatial channels will be added over the next several weeks. May 10 2007 10:37AM (jwhughes) Jerry Hughes Core Thomson scattering jwhughes
TS - Edge yes 2 lasers, 20 spatial channels. Density is cross-calibrated to the core system, based on shots 1070504014, 016, and 019. May 17 2007 09:14AM (jwhughes) Jerry Hughes Millimeter resolution edge Thomson scattering jwhughes
Vispec yes 350 and 670 nm, 4 spatial channels May 04 2007 01:02PM (agraf) Alex Graf Visible Spectrometer agraf

May 18 2007 12:14:20:093PM

System Available Comment Availability
Changed Owner Description Who Can
Change
Active MHD yes Fully operational Mar 28 2007 09:19PM (sears) Joe Snipes Active MHD Antenna sears,snipes
BES yes vertical array of six views at R ~ 87.3 cm, radial array of three views out to R ~ 89 cm, both at outboard midplane. Three discrete fiber views of beam at R ~ 70.0, 76.5 and 82.5 cm. Feb 06 2007 10:00AM (bravenec) Ron Bravenec Beam Emission Spectroscopy bravenec
Bolometers yes 2Pi diode operational, 2Pi foil being upgrade for noise resistance. Midplane foils being digitized but not calibrated, still ICRF pickup. Midplane AXUV and divertor being digitized but analyzed data not ready. Apr 26 2007 10:27AM (mlreinke) Matt Reinke Bolometers hutch,mlreinke
Boronization yes First Boronization 5/9/07 May 10 2007 04:55PM (irby) Jim Irby Boronization dekow,irby
CNPA no Jan 14 2007 02:06PM Ron Parker Compact Neutral Analyzer parker
Cryopump - Upper Divertor no In-vessel hardware is installed; in-vessel cryogenic systems are leak-tight and have passed LN2 cool-down tests. Work is proceeding on external LHe and LN2 transfer lines as well as PLC control system. Mar 30 2007 10:53AM (labombard) Brian LaBombard Upper Divertor Cryopump irby,labombard
CXRS yes The pedestal toroidal array was installed, spatially and absolutely calibrated. There are 10 chords intersect the beam at the major_R_range=[75,4:87.4]cm. Spatial resolution: 1.2 cm. The F-top poloidal array was installed and spatially calibrated. There are 19 chords intersect the beam at the major_R_range=[67.8:91.0]cm. Spatial resolution: 1.22 cm. May 01 2007 12:31PM (bespam) Bill Rowan Charge Exchange Spectroscopy bespam,blip,rachmcd,rowan
D Alpha yes \ha2_bright and \SPECTROSCOPY::TOP.VUV.VIS_SIGNALS:MCP_VIS_SIG1 are available Mar 11 2007 10:28PM (terry) Jim Terry Balmer Alpha Monitor irby,terry,wolfe
Dalsa yes camera is re-installed, and view has been calibrated Feb 26 2007 03:28PM (marmar) Earl Marmar Visible Bremsstrahlung marmar
Disruption Mitigation no Jan 14 2007 02:02PM Bob Granetz Gas Jet granetz,whyte
Divertor IR no Mar 06 2007 10:50AM Glen Wurden Divertor IR Digital Video gwurden,terry
Divertor IR Spectroscopy no Mar 06 2007 10:51AM Glen Wurden Divertor IR Spectroscopy gwurden,ldorf,terry
DNB yes All systems are operational, but as of 28 March 2007, the beam needs additional conditioning for full performance shots Mar 28 2007 09:36AM (beals) Bob Granetz Diagnostic Beam beals,granetz
FRC-ECE yes All channels now working. Apr 04 2007 11:04AM (phillips) Perry Phillips Heterodyne ECE-32 channels phillips
G-Side Ratiomatic yes The gauge is operational. Mar 30 2007 10:54AM (labombard) Brian LaBombard G-side ratiomatic ionization gauge labombard,toland
GPC yes Chs 1-8 operational. But, low and noisy signals on SOME shots, others OK. May 10 2007 10:01AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPC2 yes Most slow channels (except 1,8,10,17) operational. Set to lower freqs for LHCD. Apr 11 2007 09:34AM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt
GPI yes New view just outside of the lower X-point is operational, but data is being archived locally , not to the tree. Midplane GPI is not operational. Mar 27 2007 01:59PM (terry) Jim Terry Gas Puff Imaging terry,zweben
H/D yes spectral calibration needs to be checked, but system should be ready for the run Feb 26 2007 03:28PM (marmar) Earl Marmar H/D Ratio marmar
Hirex Jr yes Mar 06 2007 08:59AM (rice) John Rice High Resolution X-Ray ince,rice
Hirex Sr yes Storing Data, but profiles not yet available Apr 27 2007 01:20PM (ince) John Rice High Resolution X-Ray ince,rice
HXR yes Something might be wrong with channel 26; all others working fine. Mar 23 2007 10:43AM (schmidt) Ron Parker Hard X-Ray Array parker,schmidt
ICRF D-Antenna yes 80.5 MHz. ready Mar 28 2007 08:50AM (ylin) Steve Wukitch D-port antenna wukitch,ylin
ICRF E-Antenna no 80 MHz. FFT installation/coaxial line needs more work Mar 16 2007 09:32AM (ylin) Steve Wukitch E-port antenna wukitch,ylin
ICRF J-Antenna yes 78 MHz Apr 04 2007 08:56AM (ylin) Steve Wukitch J-port antenna wukitch,ylin
Lower Hybrid no 6B Pressure window failed. Arcing in 6B, 8B,9B & 23B. May 04 2007 03:44PM (dterry) Ron Parker Lower Hybrid dterry,parker
LPI yes Apr 26 2007 08:35PM (bose) Earl Marmar Lithium Pellet Injector bose,marmar
Ly-alpha yes Midplane data being digitized, but analyzed data not ready. 2D arrays being debugged. Apr 26 2007 10:28AM (mlreinke) Matt Reinke Lyman alpha cameras labombard,mlreinke
McPherson yes Working normally. Apr 19 2007 09:52AM (mlreinke) Jim Terry VUV Spectrometer mlreinke,terry
Michelson yes Operational. Mar 28 2007 08:33AM (hubbard) Amanda Hubbard ECE Te Profiles hubbard,schmidt
MKS yes E-Top, E-Bottom, F-top (cryo), G-side, and B-bottom are operational. F-top gauge has a 'sniffer tube' to measure pressures in cryopump gas box. Mar 20 2007 06:42PM (g) Brian LaBombard Baratron pressure gauges labombard
MLP no Bench tests are proceeding on a prototype MLP system. We hope to roll the system into the cell for testing in a few weeks, powering up a single electrode on the A-port scanning probe. Mar 13 2007 09:57PM (labombard) Brian LaBombard Mirror Langmuir Probe Electronics System labombard
MSE no (1) Bandpass filters replacement underway (2) Beam-into-gas spectrum measurement underway (3) Shutter mechanism currently unstable; remains open. (4) Expect beam-into-gas calibrations complete about 4/24. Apr 03 2007 12:05PM (sscott) Steve Scott Motional Stark Effect jinseok,sscott
Neutrons yes Both neutron systems are fully operational Apr 05 2007 11:19AM (fiore) Catherine Fiore Neutron Detectors fiore
Neuts and Hards yes operational Mar 21 2007 04:29PM (irby) Jim Irby X-Ray/Neutron Detector at K-Hor irby
NINJA yes All capillaries displayed by the NINJA_CONTROL GUI have been tested. NINJA puffed on 1070329009 (A-B limiter). Mar 29 2007 11:47AM (terry) Brian LaBombard NINJA gas puff labombard,terry
PCI no System unavailable. The laser is under repair. Apr 04 2007 11:16PM (lianglin) Miklos Porkolab Phase Contrast Imaging edlund,lianglin,ntsujii,porkolab
Penning Gauges yes 8 in-situ Penning ionization gauges appear to be operational: CB_DivU, CB_OutL, CB_DivL, KA_OutU, KA_OutL, B_DivL, Cryo_1, Cryo_2. Cryo_1 and Cryo_2 are new and installed in the upper cryopump 'gas-box'. Mar 13 2007 10:01PM (labombard) Brian LaBombard Penning Ionization Gauges labombard
Plasma TV yes WIDE1, WIDE2 (chan 33), DANT, JANT and DIV (without an ND filter) are operational. Mar 27 2007 01:53PM (terry) Jim Terry Video of plasma via several cameras dekow,irby,terry,wolfe
Polarimeter no Retro shutter closed Mar 15 2007 11:00AM (irby) Jim Irby C-Mod Polarimeter irby
Probe Array - ISD yes Probes at 15 of the 16 poloidal locations ('ramped' geometry) are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:47PM (labombard) Brian Labombard Inner Lower Divertor Probe Array labombard
Probe Array - LH yes All 6 probes on the lower hybrid launcher (tungsten, 1.5 mm projection) are operational. Mar 13 2007 09:46PM (labombard) Brian LaBombard Lower Hybrid Probe Array labombard
Probe Array - OSD yes Probes at 10 poloidal locations (one 'ramped' and one 'flush') are operational. n,Te, particle flux reported every 10 ms. Mar 13 2007 09:45PM (labombard) Brian LaBombard Outer Lower Divertor Probe Array labombard
Probe Array - UDIV yes 14 probes are operational ('ramped' geometry). n,Te, particle flux reported every 10 ms.Two high-gain channels are installed and operational for ECDC plasma diagnosis. Mar 13 2007 12:46PM (labombard) Brian LaBombard Upper Divertor Probe Array labombard
Reflectometer yes The 60 and 110 are connected but still being tested. The Swept frequency channel is sweeping with the waveform voltage swept at 5Hz with the voltage 4V-8V (117.8GHz-135.5GHz), also in the testing stage. May 18 2007 12:10PM (dominguez) Earl Marmar Reflectometer dominguez,marmar
Scanning Probe - ASP yes Perpendicular Mach probe head is installed. The drive is operational. Mar 15 2007 09:09PM (labombard) Brian LaBombard A-Port Scanning Probe labombard
Scanning Probe - FSP yes Perpendicular Mach probe head is installed. The probe drive is now operational. Mar 13 2007 09:51PM (labombard) Brian LaBombard F-Port Scanning Probe labombard
Scanning Probe - WASP yes A-port WASP successfully collected data on 04/04. Some intermittent open circuit on SE Electrode. K-WASP took data on 04/11. Both ready to scan as needed. Apr 12 2007 04:18PM (nsmick) Brian LaBombard Inner Wall Scanning Probe labombard,nsmick
TCI yes NL04 at 71.04 cm from 3/9/07 calibration Mar 09 2007 05:47PM (irby) Jim Irby Two-Color Interferometer (TCI) irby,murray
TS - Core yes 2 lasers, 11 spatial channels. Density is calibrated based on ECE cutoffs obtained on 4 May 2007. Additional spatial channels will be added over the next several weeks. May 10 2007 10:37AM (jwhughes) Jerry Hughes Core Thomson scattering jwhughes
TS - Edge yes 2 lasers, 20 spatial channels. Density is cross-calibrated to the core system, based on shots 1070504014, 016, and 019. May 17 2007 09:14AM (jwhughes) Jerry Hughes Millimeter resolution edge Thomson scattering jwhughes
Vispec yes 350 and 670 nm, 4 spatial channels May 04 2007 01:02PM (agraf) Alex Graf Visible Spectrometer agraf

Session Leader Comments
May 18 2007 09:10:48:833AM	1070518001	Brian Labombard	1- DN, Ip=0.8, Bt=5.6, NL04=0.82-0.7, SP @ 0.68, 0.88, 1.08s, ASP(+5), FSP(+0) Next: repeat with probes deeper and add WASP
May 18 2007 09:30:59:013AM	1070518002	Brian Labombard	2- DN, Ip=0.8, Bt=5.6, NL04=0.8-0.75, SP @ 0.68, 0.88, 1.08s, ASP(+14), FSP(+6) Next: repeat, probes deeper
May 18 2007 10:30:55:287AM	1070518006	Brian Labombard	6- DN, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-excellent, FSP(+7)-excellent Next: go to inner gap = 5mm, keeping outer gap fixed.
May 18 2007 10:45:01:073AM	1070518007	Brian Labombard	7- DN, gap=6mm, Ip=0.8, Bt=5.6, NL04=0.85-0.8, SP @ 0.68, 0.88, 1.08s, ASP(+16)-could be deeper, FSP(+7)-excellent Next: go to inner gap = 2mm, keeping outer gap fixed.
May 18 2007 10:59:06:267AM	1070518008	Brian Labombard	8- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.86-0.82, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-excellent Next: go to inner gap = 0, keeping outer gap fixed.
May 18 2007 11:13:40:490AM	1070518009	Brian Labombard	9- DN, gap=0mm, Ip=0.8, Bt=5.6, NL04=0.9, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+7)-could be deeper Next: go to inner gap = ""-2mm"", keeping outer gap fixed.
May 18 2007 11:29:09:137AM	1070518010	Brian Labombard	10- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.85, SP @ 0.68, 0.88, 1.08s, ASP(+18)-excellent, FSP(+9)-excellent Inner wall contact with this setting of clearin. Next: clearin at -13mm, keeping outer gap fixed.
May 18 2007 11:49:35:630AM	1070518011	Brian Labombard	11- DN, clearin=-13mm, Ip=0.8, Bt=5.6, NL04=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+18)-could be deeper, FSP(+11)-ok Next: repeat
May 18 2007 12:58:38:033PM	1070518012	Brian Labombard	12- DN, clearin=-13mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-excelent, FSP(+11)-excellent Next: go to clearin = -15mm
May 18 2007 12:59:35:750PM	1070518013	Brian Labombard	13- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+20)-could be deeper, FSP(+13)-could be deeper Next: repeat
May 18 2007 01:32:42:107PM	1070518014	Brian Labombard	14- DN, clearin=-15mm, NL04=0.8-0.83, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+21)-ok, FSP(+14)-ok Next: go to clearin=-17mm
May 18 2007 01:00:20:720PM	1070518015	Brian Labombard	15- DN, clearin=-17mm, NL04=0.8-0.84, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-ok, FSP(+17)-excellent Next: go to clearin=-19mm
May 18 2007 12:57:49:750PM	1070518016	Brian Labombard	16- DN, clearin=-19mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+19)-excellent Next: go to clearin=-21mm
May 18 2007 01:14:24:367PM	1070518017	Brian Labombard	17- DN, clearin=-21mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-excellent, FSP(+20)-excellent Next: go to clearin=-23mm
May 18 2007 01:31:56:500PM	1070518018	Brian Labombard	18- DN, clearin=-23mm, NL04=0.8-0.87, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+24)-first scan good, FSP(+21)-good Next: go to NL04=0.4
May 18 2007 01:39:06:220PM	1070518019	Brian Labombard	19- DN, clearin=-23mm, NL04=0.75-0.8, Bt=5.6, Ip=0.8, SP @ 0.68, 0.88, 1.08s, ASP(+23)-first scan ok, FSP(+20)-could be deeper Next: repeat
May 18 2007 01:56:41:100PM	1070518020	Brian Labombard	20- DN, clearin=-23mm, NL04=0.65-0.72, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-could be deeper, FSP(+24)-great Next: repeat
May 18 2007 02:09:16:200PM	1070518021	Brian Labombard	21- DN, clearin=-23mm, NL04=0.7, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+28)-ok, FSP(+24)-ok Next: clearin=-19mm
May 18 2007 03:53:28:160PM	1070518023	Brian Labombard	23- DN, clearin=-19mm, NL04=0.46, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+25)-ok, FSP(+20)-ok => disrupts at 1 second. Junk comes off inner wall, probably because DNB heated wall on previous no-plasma shot. Next: repeat
May 18 2007 04:09:59:810PM	1070518025	Brian Labombard	25 => disrupts at 0.7 s. Junk is still coming off inner wall. Next: reload shot#10
May 18 2007 04:19:38:563PM	1070518026	Brian Labombard	26- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.5, no probes scanning Next: repeat with probes
May 18 2007 04:54:09:200PM	1070518027	Brian Labombard	27- DN, clearin=-11mm, Ip=0.8, Bt=5.6, NL04=0.67-0.5, SP @ 0.75, 0.95, 1.15s, ASP(+18)-ok, FSP(+9)-ok Next: reload shot#16 with NL04=0.5
May 18 2007 04:43:43:760PM	1070518028	Brian Labombard	28- DN, clearin=-19mm, NL04=0.68-0.63, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+23)-could be deeper , FSP(+20)-could be deeper Next: repeat with probes deeper
May 18 2007 05:01:36:283PM	1070518029	Brian Labombard	29- DN, clearin=-19mm, NL04=0.68-0.65, Bt=5.6, Ip=0.8, SP @ 0.75, 0.95, 1.15s, ASP(+26)-ok , FSP(+22)-ok Next: reload shot#8 with NL04=0.5
May 18 2007 05:24:29:383PM	1070518030	Brian Labombard	30- DN, gap=3mm, Ip=0.8, Bt=5.6, NL04=0.52, SP @ 0.75, 0.95, 1.15s, ASP(+19)-excellent, FSP(+8)-excellent

Physics Operator Comments
May 17 2007 05:35:50:577PM		Ron Parker	Engineering Setup ------------------ Overnight ECDC in D2, p_fill = 2e-4 Run begins at 09:00 (lock-up at 08:30) and ends at 17:00 Power systems as on 1070511029 Acoil: +Dtop -Dbot -Jtop +Jbot (standard) Hybrid Enabled Gas setup: --------- fill B-Top with 6 psi D2 : Hybrid enabled (PG4) fill B-side lower with 1 psi Ar : Hybrid DISABLED (PG1) leave B-side upper as is : Hybrid DISABLED (PG2) fill B-main (C-side) with 40 psi D2 : Hybrid enabled (PG3) pump out NINJA and backfill with 10 PSI of D2, then enable. Enable the following gate valves and shutters: ECE, VUV, Z-bolo shutters Torvac setup: Pumpstack gatevalves OPEN RGAs on ICRF: {Steve Wukitch - please specify} LH: None Run Plan: See Session Leader Plan for shot sequence.
May 18 2007 09:03:09:813AM	1070518001	Ron Parker	Good morning. Machine ready to go. Shot 1070511029 loaded with the following mods: B_T =5.6 T, nl_04=8e19 m-2, ssep = 0.
May 18 2007 09:32:30:123AM	1070518001	Ron Parker	Shot 1 ran well, probably will be the best of the day.
May 18 2007 09:34:53:530AM	1070518002	Ron Parker	Shot 2 ran OK. More or less the same as shot 1.
May 18 2007 09:39:10:377AM	1070518003	Ron Parker	Shot 3 fizzled. Early breakdown but burnout is slow. No changes for next shot, see if it goes.
May 18 2007 09:57:09:117AM	1070518004	Ron Parker	Shot 4 disrupted early, 0.18 s. Too much gas. Try again.
May 18 2007 10:03:14:667AM	1070518005	Ron Parker	Shot fizzled, not surprising after disruption on previous shot.
May 18 2007 10:07:50:810AM	1070518005	Ron Parker	For next shot, reduce BR(0) from 0.0038 to 0.0030
May 18 2007 10:29:17:083AM	1070518006	Ron Parker	Shot 6 ran OK. JT finds Halpha filter had fallen off, explaining large Halpha signals. Next: Reduce inner gap from 11 to 5 mm, keeping outer gap the same by reducing Rcur by 3 mm.
May 18 2007 10:48:16:480AM	1070518007	Ron Parker	Shot 7 ran OK. Next: Reduce inner gap by 3 mm, Rcur by 1.5 to keep outer gap constant.
May 18 2007 10:59:25:437AM	1070518008	Ron Parker	Shot 8 looked good. Next: Reduce clearin by 3 mm, Rcur by 1.5.
May 18 2007 11:14:20:663AM	1070518009	Ron Parker	Shot 9 ran. Next: Reduce clearin by 2 mm, Rcur by 1.
May 18 2007 11:25:51:980AM	1070518010	Ron Parker	Shot 10 ran OK. Next: Clearin reduced by 2mm, from -11 to -13 mm and Rcur by 1 mm from 652 to 651 mm.
May 18 2007 11:47:25:827AM	1070518011	Ron Parker	Shot 11 ran well, repeat for next shot.
May 18 2007 11:55:22:213AM	1070518012	Ron Parker	Shot 12 ran well. Reduce Clearin again by 2 mm, from -13 mm to -15 mm and Rcur by 1, from 651 to 650.
May 18 2007 12:08:39:560PM	1070518013	Ron Parker	Shot 13 ran OK, disrupting on current rampdown around 200 kA. Repeat for next shot.
May 18 2007 12:25:03:880PM	1070518014	Ron Parker	Shots are rolling along. Next: Reduce Clearin by 2 more mm, from -15 to -17 mm, and Rcur by 1,from 650 to 649 mm.
May 18 2007 12:41:12:697PM	1070518015	Ron Parker	Shot 15 looked good. Next: Brian is relentless - reduce Clearin by 2 more mm for next shot. Reduce Clearin by 2mm, from -17 to -19 mm, but this time leave Rcur at 649 (since the outer gap seems to be growing).
May 18 2007 12:54:24:517PM	1070518016	Ron Parker	Shot 16 ran well. Next: Continue Clearin scan inward. Reduce Clearin from -19 to -21, no change for Rcur.
May 18 2007 01:25:00:057PM	1070518017	Ron Parker	Shot 17 was OK, although startup was a bit dicey. For shot 18, reduce Clearin by 2 more mm, from -21 to -23 mm. Again, no change for Rcur
May 18 2007 01:25:34:403PM	1070518018	Ron Parker	Shot 18 ran well, startup better than shot 17, but no change was made. Next: same gaps, nl_04 reduced to 4e19.
May 18 2007 01:34:01:530PM	1070518019	Ron Parker	019. Plasma. Shot was OK
May 18 2007 01:47:10:287PM	1070518020	Ron Parker	020. Plasma. The goal is nl_04=0.4e+20. nl_04 is actually 0.7e+20
May 18 2007 02:00:17:040PM	1070518021	Ron Parker	021. Plasma. nl_04=0.7e+20
May 18 2007 02:20:33:800PM	1070518021	Ron Parker	Next shot: Returning to approximately the setup of shot 016. The only change is that CLEARIN is changed to -0.019 for this shot. After shot 021, there was a "bang". The concensus was that this came from the power room. An inspection revealed nothing.
May 18 2007 02:23:00:220PM	1070518022	Ron Parker	022. Power supply problems. OH2U
May 18 2007 02:39:29:070PM	1070518022	Ron Parker	022. Power supply problems. OH2U Problem has been diagnosed and traced to a broken connection in the commutation network. Short delay while problem is fixed.
May 18 2007 03:43:03:173PM	1070518023	Ron Parker	Shot 23 was ugly -- started up but disrupted just after 1 s. Steve reports that EF power supply is railing during the shot --but it ran all day like this?!
May 18 2007 03:47:47:487PM	1070518024	Ron Parker	Shot 24 fizzled, not surprising after disruption on 23. Beam is giving some problems due to firing without plasma. Beam valve disabled in order to try to finish run plan.
May 18 2007 04:09:26:747PM	1070518025	Ron Parker	Shot 25 disrupted at ~ 700 ms.
May 18 2007 04:29:14:363PM	1070518026	Ron Parker	Shot 26 ran well, Brian's probes were not set properly for this shot and we'll repeat.
May 18 2007 04:30:49:740PM	1070518027	Ron Parker	Shot 27 ran, we'll move the Clearin out to -19, similar to shot 16 but with lower density.
May 18 2007 04:56:09:077PM	1070518028	Ron Parker	Decent shot, a bit bumpy current rise but usable. Probes weren't deep enough so we'll repeat.
May 18 2007 04:53:56:967PM	1070518029	Ron Parker	Shot 29 ran OK, not a pretty startup but flattop OK. Next and final shot: Repeat of shot 8 with lower density.
May 18 2007 05:10:29:847PM	1070518030	Ron Parker	Shot 30 was OK, disrupted on ramp down @ ~ 500 kA.

Engineering Operator Comments
Shot	Time	Type	Status	Comment
1	09:03:29:080AM	Plasma	Ok
2	09:17:18:023AM	Plasma	Ok
3	09:29:54:763AM	Plasma	Ok
4	09:42:46:767AM	Plasma	Ok
5	09:59:43:557AM	Plasma	Ok
6	10:12:15:857AM	Plasma	Ok
7	10:34:44:507AM	Plasma	Ok
8	10:49:08:170AM	Plasma	Ok
9	11:02:02:783AM	Plasma	Ok
10	11:16:11:570AM	Plasma	Ok
11	11:35:00:593AM	Plasma	Ok
12	11:47:56:337AM	Plasma	Ok
13	12:01:45:870PM	Plasma	Ok
14	12:14:43:327PM	Plasma	Ok
15	12:29:59:960PM	Plasma	Ok
16	12:42:56:667PM	Plasma	Ok
17	12:57:07:093PM	Plasma	Ok
18	01:11:30:320PM	Plasma	Ok
19	01:29:58:060PM	Plasma	Ok
20	01:43:52:363PM	Plasma	Ok
21	01:56:52:180PM	Plasma	Ok
22	02:17:33:377PM	Plasma	Bad	OH2U comm flt
23	03:27:27:887PM	Plasma	Ok
24	03:43:15:750PM	Plasma	Ok
25	03:58:03:710PM	Plasma	Ok
26	04:10:59:030PM	Plasma	Ok
27	04:23:58:970PM	Plasma	Ok
28	04:36:43:430PM	Plasma	Ok
29	04:49:51:950PM	Plasma	Ok
30	05:02:54:470PM	Plasma	Ok