Miniproposals

Miniproposal: 536 Date Filed: 2/21/2008 Title: Evaluation of FWEH, FWCD and MCCD First Author: Steve Wukitch Session Leader: Steve Wukitch (shots 1-25)

Engineering Operator Run Comment

MP??? - Fast wave electron heating at 50 MHz SS: Wukitch PO: Irby

Session Leader Plans

Entered: Nov 18 2009 10:29:21:397PM

Author: Steve Wukitch

Cryopump is required for this run. FRCECE and GPC are critical for this run diagnostics - primary magnetic field will be ~5.2 T. All transmitters required - we will wait for FMIT#1 (D antenna) to be fixed this morning. 1. Optimize initial target plasma for high central temperature and moderate density. Need to stay out of H-mode. a. Start with 1091118020 - target density nl04~0.7, cryopump on b. increase D/E power to 3 MW, J power to ~2.6 MW, Ar puff at 0.6 for 0.15 s c. scan density - best mix of high electron temperature and controlled Prad d. scan plasma current 1.3 MA (disruption issue?), 0.8 MA, 0.6 MA 2. Using optimum conditions, modulate J power a. Widely spaced, full power switch off b. periodic modulation, slow compared to sawtooth period - 25%, 50%,100% power modulation c. periodic modulation, fast compared to sawtooth period - 25%, 50%,100% power modulation 3. Repeat under optimum conditions using +/-90deg

Physics Operators Plans

Entered: Nov 18 2009 03:35:49:150PM

Author: Jim Irby

MP??? - Fast wave electron heating at 50 MHz SS: Wukitch PO: Irby ----------------- Engineering Setup ----------------- Run begins at 10:00 and ends at 17:00 Power systems as on: 1091118020 Acoil: +Dtop -Dbot -Jtop +Jbot (standard) Hybrid Enabled Gas setup: Fill B-Top with 6 psi D2 Hybrid enabled (PG4) fill B-side lower with 1 psi Ar Hybrid DISABLED (PG1) leave B-side upper as is Hybrid DISABLED (PG2) fill B-main (C-side) with 40 psi D2 Hybrid enabled (PG3) fill NINJA with 10 psi D2 DISABLED Enable gatevalves and shutters: ECE, VUV, Z-bolo Torvac gatevalve toggle (yes/no): no Boronization(yes/no): no Overnight ECDC (yes/no): yes ICRF(yes/no): yes LH(yes/no): no DNB(yes/no): no Cryopump (yes/no): no Vessel temperature: 35/35/35 ------------------------------ ECDC Parameters ------------------------------ gas and pressure: D2 at 2e-4 Torr sweep: 44/45/103 cm scan: 20/120 s

Session Leader Summaries

Entered: Nov 20 2009 10:43:40:537AM

Author: Steve Wukitch

After a delayed start to fix FMIT#1 fused fast breaker control circuit, we got initially good FWEH results with Ar puff and then tried to optimize. Discharges 002-004 are the best FWEH examples we have but and then we made a mess. The details are that we tried to utilize Ne at a constant level but this appeared to be elusive. We then returned to Ar puff at 1 psi plenum pressure and plasma response was better. By shot 019, the plasma could tolerate no Ar and the J antenna without impurity seeding injected impurities and evolved lots of gas. The startup was plague by lots of runaways which was not good. We also lost the FFT on 010 so the match was reasonable for E antenna but it did not follow the load.

Physics Operator Summaries

Entered: Nov 20 2009 07:58:23:977AM

Author: Jim Irby

We started a little more than an hour late this morning since time was required to fix the fmit#1 breaker (we could not spin up alternator with the alc2 breaker open). By shot 04 we were doing ok with a full length plasma, lots of argon as required for the MP, and no hards. Then on shot 05 the hards saturated early and the plasma was lost by 250 ms. Shots 24 and 25 late in the day had very similar behavior. The next plasma attempt was shot 08, in which the argon was replaced with neon, but it only lasted for 700 ms. The next full length shot was 10, but neon was not seen in the plasma until very late in the discharge. We had several full length plasmas until shot 15 when the discharges disrupted early until shot 19 for which we disabled the argon. Plasmas were intermittent the rest of the day with several lasting less than 200 ms with hards starting at 20 to 30 ms. Increasing the prefill did not help, but field tweaks may have if we had more time to try. The mystery for the day was the very different behavior of argon and neon. Argon was easily seen by the spectrometry, but not neon. A probable explanation is different pumping speeds to the cryopump. Besides issues with disruptions, we also had problems controlling the density. A combination of impurity puffing and cryopumping seems to have made control difficult. We tried different prop gains on nl_04 feedback without success. Gains as low a 3 were tried which resulted in never reaching the target. no power 06, 07 --- data system issues fizzles 09,11,17,23

Session Leader Comments
Nov 19 2009 10:41:39:673AM	1091119001	Steve Wukitch	plasma - flash heating @0.878s no Ar density was a bit wiggly despite cryopump - gains may need adjustment next: enable Ar, smooth density waveform, increase D/E power to 2.5 MW
Nov 19 2009 11:01:26:300AM	1091119002	Steve Wukitch	plasma - flash heating late Ar enabled good FWEH density was still wiggly despite cryopump next: smooth density waveform, lower density to nl04~0.6
Nov 19 2009 11:05:44:283AM	1091119003	Steve Wukitch	plasma - full length despite Ar puff good RF pulses and good heating observed with FW next: keep working on density waveform, extend D/E front porch
Nov 19 2009 12:02:45:160PM	1091119005	Steve Wukitch	plasma - early disruption - lots of hard x-rays
Nov 19 2009 12:02:54:360PM	1091119006	Steve Wukitch	no power
Nov 19 2009 12:03:08:207PM	1091119007	Steve Wukitch	no power
Nov 19 2009 12:49:51:633PM	1091119008	Steve Wukitch	plasma ended at 0.72 sec - seems to be a brick lots of computer related issues Ne seeding using 1 psi and starting 150 ms prior to RF (@0.5 s)
Nov 19 2009 12:50:00:023PM	1091119009	Steve Wukitch	fizzle
Nov 19 2009 01:14:17:247PM	1091119010	Steve Wukitch	plasma no I-mode on this shot Te is lower even for the D/E portion Ar signal is low/neon too much/too little next: increase Ne plenum pressure to 1.5 psi
Nov 19 2009 01:47:27:827PM	1091119012	Steve Wukitch	plasma neon was at 1.5 psi and looks too high next: Ne plenum pressure to 0.5 psi
Nov 19 2009 02:10:29:560PM	1091119013	Steve Wukitch	plasma heating is better hard x-rays are high next: back to Ar as 004 (two pulses)
Nov 19 2009 02:41:15:780PM	1091119014	Steve Wukitch	plasma heating is better next: increase Ar to 2 psi
Nov 19 2009 02:46:44:247PM	1091119015	Steve Wukitch	early disruption
Nov 19 2009 03:24:22:450PM	1091119016	Steve Wukitch	early disruption
Nov 19 2009 03:24:03:217PM	1091119017	Steve Wukitch	early disruption
Nov 19 2009 03:23:55:217PM	1091119018	Steve Wukitch	early disruption
Nov 19 2009 03:44:19:247PM	1091119019	Steve Wukitch	plasma no Ar puff heating is less effective than 014 next: 2 psi Ar is too high, 1 psi worked for 014 - use 1 psi Ar
Nov 19 2009 04:18:05:153PM	1091119021	Steve Wukitch	plasma disruption @1.83 s next: move RF timing
Nov 19 2009 04:56:55:513PM	1091119023	Steve Wukitch	no plasma
Nov 19 2009 04:56:17:920PM	1091119024	Steve Wukitch	no plasma
Nov 19 2009 04:57:09:607PM	1091119025	Steve Wukitch	no plasma

Physics Operator Comments
Nov 19 2009 08:08:35:470AM		Jim Irby	approx 08:00 --- FMIT#1 breaker operating again, alternator starting up
Nov 19 2009 10:10:19:910AM		Jim Irby	alternator at 1140 RPM estimated start time: 10:30 alternator up to speed --- doing search
Nov 19 2009 10:29:50:830AM	1091119001	Jim Irby	load from 1091118020 loaded open tree done Params from 1091118020: Upper null, 1 MA, nl04 request of 0.4e20/m^2, pg1 at 100% from 0.3 to 0.425 s. in seg 2, pg3 100% ramp down to 0% at 100 ms. pg1 from 0.3 to 0.45 s Bt to 5.2 T --- 145 kA pg4 from -0.550 to -0.500 s --- cryopump on nl04 density request to 0.7e20/m^2 open tree done -------------------------- igt at 1.9e-8 Torr --- Cryopump running plasma for 0.87 s --- 4 MW of RF hards ok
Nov 19 2009 10:46:44:610AM	1091119002	Jim Irby	changes -------------------------------- Argon enabled at 2 psi --- forgot to ask for it for shot 1 Increased early density request to fill in drop in nl at 0.4 s loaded results -------------------------------- igt 1.3e-7 Torr plasma for 1.40 s --- density oscillating around request
Nov 19 2009 11:02:47:237AM	1091119003	Jim Irby	changes -------------------------------- nl_04 prop gain from 10 to 6 pg2 to 0% nl_04 request from 0.7 to 0.6e19/m^2 loaded results -------------------------------- igt 2.3e-7 Torr plasma into rampdown --- rf ramped down nicely after 1.5 s 5.2 MW of rf still no control of density?? lots of hards
Nov 19 2009 11:22:01:533AM	1091119004	Jim Irby	changes -------------------------------- decreased ramp-down rate of pg3 gas in seg 1 loaded argon injection from 0.3 to 0.5 s second argon pulse added from 1.0 to 1.1 s results -------------------------------- plasma into rampdown --- saturated hards --- still no density control
Nov 19 2009 11:47:58:520AM	1091119005	Jim Irby	changes -------------------------------- nl_04 prop gain from 6 to 3 pre-puff increased from 50 to 60 ms --- reduce hards? loaded results -------------------------------- igt 1.7e-7 Torr plasma for 0.264 s --- major injection around 45 ms
Nov 19 2009 11:50:53:410AM	1091119006	Jim Irby	no power shot --- data system issue
Nov 19 2009 12:05:22:393PM	1091119007	Jim Irby	changes -------------------------------- no changes data system problem again --- no power shot results --------------------------------
Nov 19 2009 12:26:04:987PM	1091119008	Jim Irby	changes -------------------------------- pumped out argon and replaced with neon at 1 psi neon pulse from 0.5 to 1.4 s loaded ef4 from -1300 to -1275 A loaded results -------------------------------- igt 7.2e-8 Torr plasma for 0.718 s --- injection? hards are gone --- ef4, prefill? still have data system issues --- analysis not running
Nov 19 2009 12:49:35:570PM	1091119009	Jim Irby	changes -------------------------------- nl_04 request back to 7 from 6e19/m^2 --- lower prop gain makes getting density more difficult? results -------------------------------- cryopump dump in INIT --- holding as long as we can fizzle
Nov 19 2009 01:02:27:420PM	1091119010	Jim Irby	changes -------------------------------- none results -------------------------------- igt 1.3e-7 Torr plasma for 1.607 s --- still no hards
Nov 19 2009 01:24:03:620PM	1091119011	Jim Irby	changes -------------------------------- no neon seen on shot 10 --- neon pressure from 1 to 1.5 psi results -------------------------------- fizzle
Nov 19 2009 01:50:05:153PM	1091119012	Jim Irby	changes -------------------------------- ef4 back to -1300 from -1275 A pre-puff from 60 to 55 ms loaded results -------------------------------- plasma into rampdown, but hards are back
Nov 19 2009 01:58:06:217PM	1091119013	Jim Irby	changes -------------------------------- neon pressure from 1.5 to 0.5 psi ef4 from -1300 to -1290 A loaded results -------------------------------- igt 1.9e-7 Torr plasma for 1.60 s --- lots of hards
Nov 19 2009 02:23:25:230PM	1091119014	Jim Irby	changes -------------------------------- pre-fill to 58 ms from 55 loaded argon replaces neon at 1 psi argon from 0.3 to 0.5 and 1.0 to 1.1 s loaded results -------------------------------- plasma for 1.635 s, hards are gone, nice neutron rates, 5.2 MW rf
Nov 19 2009 02:47:39:967PM	1091119015	Jim Irby	changes -------------------------------- argon to 2 psi Before this shot we entered cell to verify neon bottle setup (which was found to be proper). Matt sees argon but does not see neon. Argon signal scales with argon pressure, but no neon seen at any pressures tried so far. This mystery is made worse by the current state of the RGA which needs to be sent back for repair. results -------------------------------- plasma for 0.565 s
Nov 19 2009 02:59:20:513PM	1091119016	Jim Irby	changes -------------------------------- try again results -------------------------------- plasma for 0.55 s --- locked mode?
Nov 19 2009 03:13:35:653PM	1091119017	Jim Irby	changes -------------------------------- import seg 2 from 1091119004 into seg 2: prop gain back to 6 loaded results -------------------------------- fizzle ---- cryopump did us in we think --- prefill pressure factor of two high
Nov 19 2009 03:23:56:607PM	1091119018	Jim Irby	changes -------------------------------- no changes results -------------------------------- plasma for 0.539 s --- we will disable the argon next shot
Nov 19 2009 03:43:19:480PM	1091119019	Jim Irby	changes -------------------------------- argon disabled nl_04 request from 0.6e20 to 0.8e20/m^2 loaded results -------------------------------- plasma into rampdown, still no density control, but there was density!
Nov 19 2009 03:55:54:730PM	1091119020	Jim Irby	changes -------------------------------- argon pressure reduced to 1 psi from 2 psi and enabled results -------------------------------- plasma for 0.844 s
Nov 19 2009 04:08:45:090PM	1091119021	Jim Irby	changes -------------------------------- 1st argon puff from 0.4 to 0.5 s (was 0.3 to 0.5 s) loaded results -------------------------------- plasma for 0.84 s
Nov 19 2009 04:33:10:980PM	1091119022	Jim Irby	changes -------------------------------- delay in rf results -------------------------------- plasma into rampdown
Nov 19 2009 04:39:55:827PM	1091119023	Jim Irby	changes -------------------------------- no dpcs changes results -------------------------------- plasma for 90 ms --- lost by 30 ms
Nov 19 2009 04:48:36:950PM	1091119024	Jim Irby	changes -------------------------------- no dpcs changes results -------------------------------- plasma for 0.23 s --- objects fall in --- lots of hards
Nov 19 2009 05:00:41:780PM	1091119025	Jim Irby	changes -------------------------------- prefill increased to 60 ms from 58. results -------------------------------- plasma (sort of) for 80 ms --- still lots of hards give up and clean up overnight...
Nov 20 2009 09:23:02:037AM	1091119025	Bill Rowan	001. no power data acquisition

Engineering Operator Comments
Shot	Time	Type	Status	Comment
1	10:23:38:673AM	Plasma	Ok
2	10:41:37:063AM	Plasma	Ok
3	10:55:51:423AM	Plasma	Ok
4	11:15:50:783AM	Plasma	Ok
5	11:30:09:770AM	Plasma	Ok
6	11:49:17:550AM	Plasma	Bad	no power act failure
7	11:59:00:910AM	Plasma	Bad	no power act failure
8	12:13:49:237PM	Plasma	Ok
9	12:41:39:553PM	Plasma	Ok
10	12:56:04:870PM	Plasma	Ok
11	01:20:03:933PM	Plasma	Ok
12	01:34:00:467PM	Plasma	Ok
13	01:51:47:200PM	Plasma	Ok
14	02:16:52:293PM	Plasma	Ok
15	02:39:52:183PM	Plasma	Ok
16	02:52:19:730PM	Plasma	Ok
17	03:06:34:027PM	Plasma	Ok
18	03:19:41:577PM	Plasma	Ok
19	03:32:36:247PM	Plasma	Ok
20	03:47:26:280PM	Plasma	Ok
21	04:01:04:560PM	Plasma	Ok
22	04:16:33:153PM	Plasma	Ok
23	04:29:42:763PM	Plasma	Ok
24	04:42:15:560PM	Plasma	Ok
25	04:54:47:700PM	Plasma	Ok

System Availability

Nov 19 2009 10:23:07:533AM

System Available Comment Availability Changed Owner Description Who Can Change Active MHD no secured - tagged out Jun 02 2008 11:03AM (sears) Joe Snipes Active MHD Antenna sears,snipes BES yes 7 horizontal views spread out R_maj=[0.72-0.9m], 3 cm over the tokamak midplane (beam) Jul 09 2009 05:12PM (bespam) Bill Rowan Beam Emission Spectroscopy bespam,liao,rowan Bolometers yes 2pi (diode+foil), AXA, AXJ, WB3AX, WB4AX, LEDGE-AX working fine. MID-FOILS working fine. The LEDGE/DIV foils still need calibrations applied Aug 27 2009 09:09AM (mlreinke) Matt Reinke Bolometers hutch,mlreinke Boronization yes   Nov 13 2009 06:37AM (dekow) Jim Irby Boronization dekow,irby CNPA no Single channel CNPA available as of 12/1707 Jun 10 2009 10:22AM (twf) Ron Parker Compact Neutral Analyzer parker Cryopump - Upper Divertor yes Operational Nov 09 2009 09:12AM (irby) Brian LaBombard Upper Divertor Cryopump irby,labombard CXRS yes The wide-view toroidal array was installed, spatially and absolutely calibrated. There are 7 toroidal chords intersect the beam at the major_R_range=[74.2:83.6]cm. Spatial resolution: 1.2 cm. The F-top wide-view poloidal array was installed and spatially calibrated. There are 19 chords intersect the beam at the major_R_range=[0.65:0.9.]m. Spatial resolution: 1.22 cm. Jul 09 2009 05:16PM (bespam) Bill Rowan Charge Exchange Spectroscopy bespam,blip,liao,rachmcd,rowan D Alpha yes \ha2_bright is available; \SPECTROSCOPY::TOP.VUV.VIS_SIGNALS:MCP_VIS_SIG1 is not available Jul 01 2009 09:45AM (terry) Jim Terry Balmer Alpha Monitor irby,terry,wolfe Dalsa yes system is aligned and operating; not yet calibrated Jul 14 2009 02:22PM (marmar) Earl Marmar Visible Bremsstrahlung marmar Disruption Mitigation yes operational, but turned off Nov 03 2009 04:59PM (granetz) Robert Granetz Gas Jet granetz,whyte Divertor IR no   Mar 06 2007 10:50AM  Glen Wurden Divertor IR Digital Video gwurden,terry Divertor IR Spectroscopy no   Mar 06 2007 10:51AM  Glen Wurden Divertor IR Spectroscopy gwurden,terry DNB no in test mode only Nov 03 2009 05:01PM (granetz) Robert Granetz Diagnostic Neutral Beam dterry,granetz,gung ECDC yes   Nov 09 2009 09:13AM (irby) Jim Irby 2.45 GHz, 3 kW, discharge cleaning system dekow,irby,pfeiffer FRC-ECE yes All 32 channels working and calibrated. Oct 06 2009 11:17AM (phillips) Perry Phillips Heterodyne ECE-32 channels phillips G-Side Ratiomatic yes Gauge installed. Controller repaired. Aug 23 2009 10:36PM (toland) Brian LaBombard G-side ratiomatic ionization gauge labombard,toland Glow Discharge no 6/10/09: Paddles meggered at 1000 v to machine ground (>300 Mohm) prior to closing the vacuum chamber. Plugs for Power Supply and Controls Unplugged and Red Tagged, Safe for In-Vessel Access Jun 10 2009 01:47PM (dekow) Jim Irby 1 kV, 5 A, glow discharge system dekow,dterry,irby GPC yes Operational. Jul 28 2009 04:23PM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt GPC2 yes Most channels operational. Jul 28 2009 04:23PM (hubbard) Amanda Hubbard ECE Polychromater hubbard,schmidt GPI yes The Xpt-view, the midplane-view cameras are operational. The innerwall GPI (coupled to the fast-diodes) is available. Jul 01 2009 09:45AM (terry) Jim Terry Gas Puff Imaging terry,zweben H/D yes poses no safety hazard for people working around the machine Jun 18 2009 01:04PM (marmar) Earl Marmar H/D Ratio marmar HEAT yes   Oct 27 2009 10:39AM (dekow) Gary Dekow - Machine Heaters - burke,dekow Hirex Jr yes Hirex-Jr has been installed and tested Jun 17 2009 11:54AM (rice) John Rice High Resolution X-Ray ince,rice Hirex Sr yes currently only one detector is operational, off-axis He-like argon emission Jul 14 2009 10:01AM (rice) John Rice High Resolution X-Ray ince,rice HXR no In safe mode (high voltage turned off) May 27 2008 09:19PM (schmidt) Ron Parker Hard X-Ray Array parker,schmidt ICRF D-Antenna yes operational at 80 MHz Jul 21 2009 04:49PM (wukitch) Steve Wukitch D-port antenna wukitch,ylin ICRF E-Antenna yes antenna and FFT operational Jul 21 2009 04:49PM (wukitch) Steve Wukitch E-port antenna wukitch,ylin ICRF J-Antenna yes available at 80 MHz and [0,pi,0,pi] phasing Sep 04 2009 10:01AM (wukitch) Steve Wukitch J-port antenna wukitch,ylin Laser Blow-Off yes Requires some advance notice for laser start-up Oct 16 2009 12:46PM (g) Martin Greenwald Impurity Injection System g,nthoward Lower Hybrid no Breaker locked and tagged out. Waveguide disassembly started. Open Waveguides have been shorted. May 28 2008 09:47AM (dterry) Ron Parker Lower Hybrid dterry,parker,wallaceg LPI no Beam line removed May 30 2008 02:09PM (bose) Earl Marmar Lithium Pellet Injector bose,marmar Ly-alpha yes Midplane, WB4-LY, LEDGE-LY all collecting data. WB1-LY not attached. Aug 27 2009 09:10AM (mlreinke) Matt Reinke Lyman alpha cameras labombard,mlreinke McPherson yes Operating normally Aug 27 2009 09:10AM (mlreinke) Jim Terry VUV Spectrometer mlreinke,terry Michelson yes Operational. Recalibrated 7/27/09. Jul 28 2009 04:22PM (hubbard) Amanda Hubbard ECE Te Profiles hubbard,schmidt MKS yes Gauges are on. B-bottom is not operating - bad sensor head? Jul 14 2009 09:12PM (labombard) Brian LaBombard Baratron pressure gauges labombard MLP no System is in edge lab. Version 2 drivers ready to test. Needs a student to help work on it. Jul 14 2009 09:20PM (labombard) Brian LaBombard Mirror Langmuir Probe Electronics System labombard MSE no As of 6/10/09, MSE is calibrated & ready to go. Awaiting DNB. Jun 10 2009 10:34AM (sscott) Steve Scott Motional Stark Effect jinseok,sscott Neutrons yes Neutron detectors are calibrated and ready to go. Voltages will be turned on prior to first plasma. Jun 10 2009 10:35AM (fiore) Catherine Fiore Neutron Detectors fiore Neuts and Hards yes Power back on morning of 11/09 before run Nov 09 2009 09:10AM (irby) Jim Irby X-Ray/Neutron Detector at K-Hor irby NINJA no Capillaries were tested in-vessel. Plenum has a leak and needs fixing. Jul 14 2009 09:14PM (labombard) Brian LaBombard NINJA gas puff labombard,terry PCI yes Operational. Nov 12 2009 02:36PM (ntsujii) Miklos Porkolab Phase Contrast Imaging arai,edlund,ennever,ntsujii,porkolab Penning Gauges yes High voltage is enabled (on during INIT, off during RECOOL). Jun 30 2009 09:42PM (labombard) Brian LaBombard Penning Ionization Gauges labombard Plasma TV yes WIDE1, WIDE2 (chan 33), DANT, JANT and DIV are operational. Jul 01 2009 09:46AM (terry) Jim Terry Video of plasma via several cameras dekow,irby,terry,wolfe Polarimeter no Safe for Machine Entry Sep 14 2007 12:17PM (irby) Jim Irby C-Mod Polarimeter irby Power - Alternator Air Switch yes Checked and Operational as of 06/18/09 Jun 19 2009 08:04AM (irby) Gary Dekow feeds all the other supplies cochran,dekow,dterry,irby Power - PEI yes   Nov 13 2009 06:38AM (dekow) Gary Dekow PEI System cochran,dekow,dterry,irby Power - TMX yes Checked out and ready for Magnet Tests as of 06/18/09 Jun 19 2009 08:07AM (irby) Gary Dekow Ef2s,. EFCs and A-Coils byford,cochran,dekow,dterry,irby Power Systems yes Checked out and ready for Magnet Tests as of 06/18/09 Jun 19 2009 08:07AM (irby) Jim Irby C-Mod Magnet Supplies byford,cochran,dekow,dterry,irby Probe Array - ISD yes Array is operational with new cPCI data system. Probe 14 has open circuit. Jul 14 2009 09:17PM (labombard) Brian Labombard Inner Lower Divertor Probe Array labombard Probe Array - LH no LH launcher not installed. Cables are unplugged at the A-port rack. Jul 14 2009 09:16PM (labombard) Brian LaBombard Lower Hybrid Probe Array labombard Probe Array - OSD yes Array is operational with new cPCI data system. Jul 14 2009 09:16PM (labombard) Brian LaBombard Outer Lower Divertor Probe Array labombard Probe Array - UDIV yes Array is operational with new cPCI data system. Probe 13 has a bad cable (open). Jul 14 2009 09:17PM (labombard) Brian LaBombard Upper Divertor Probe Array labombard Reflectometer yes Since 1091112000, 110 channel has been reinstalled. All channels are operational. Nov 12 2009 09:19AM (dominguez) Earl Marmar Reflectometer dominguez,marmar Scanning Probe - ASP yes Probe is operational. Needs plasma conditioning. Jul 14 2009 09:18PM (labombard) Brian LaBombard A-Port Scanning Probe labombard Scanning Probe - FSP yes Probe is operational. Needs plasma conditioning. Jul 14 2009 09:18PM (labombard) Brian LaBombard F-Port Scanning Probe labombard Scanning Probe - WASP yes System connected to A-port WASP. Needs plasma testing. Jul 14 2009 09:19PM (labombard) Brian LaBombard Inner Wall Scanning Probe labombard,nsmick Sparker yes Sparker back in operation before 11/09 run Nov 09 2009 09:11AM (irby) Jim Irby Field Emission Preionization for C-Mod dekow,irby,parkin TCI yes System restarted and aligned. Several chords available including NL04. Density Feedback available. Ready for plasma. Jun 18 2009 09:15AM (murray) Jim Irby Two-Color Interferometer irby,murray TS - Core yes 2 lasers working. 15 spatial channels operational. Calibrated Oct 13 2009 07:49PM (yma) Jerry Hughes Core Thomson scattering jwhughes,yma,zhang TS - Edge yes Operational, and calibrated. Oct 11 2009 03:01PM (jwhughes) Jerry Hughes Millimeter resolution edge Thomson scattering jwhughes,yma,zhang Vispec no 350 and 670 nm, 4 spatial channels Nov 28 2007 09:58AM (agraf) Alex Graf Visible Spectrometer agraf XTOMO yes Operating normally Aug 27 2009 09:10AM (mlreinke) Bob Granetz X-Ray Tomography granetz,mlreinke

Nov 20 2009 09:16:27:100AM

001. no power data acquisition

Nov 20 2009 09:21:35:990AM

001. no power data acquisition