| Miniproposals | ||||||||||
| ||||||||||
|
| Operators | |
| Session leader(s): | Greg Wallace,Steve Wukitch |
| Physics operator(s): | Yijun Lin |
| Engineering operator(s): | Sam Pierson,Gary Dekow,Thomas Toland |
| Engineering Operator Run Comment |
| MP681 Evaluate Field-Aligned Antenna (post-boronization) |
| Session Leader Plans |
| Entered: Jun 13 2012 02:30:49:033PM |
| Author: Greg Wallace |
| SL_Plan for 1120614
MP 605 LH setup: Launcher at 1278 (0.3 mm behind limiter) 90 deg phasing 50 kW/klystron to max available power Pulse timing 0.8-1.3 s 1) Load shot 1120612006. (Low density, 500 kA L-mode.) Set LH power to 50 kW/klystron at 40 kV. 2) If step 1 is successful, increase to 80 kW/klystron at 40 kV. 3) If step 2 is successful, increase to 110 kW/klystron at 50 kV. 4) If step 3 is successful, increase in increments of 20 kW/klystron and continue. |
| Entered: Jun 14 2012 08:44:00:900AM |
| Author: Steve Wukitch |
| ------------------------------
Session Leader Plan - Part b ------------------------------ MP681: Evaluate Field-Aligned Antenna Characterize FA-J antenna performance post-boronization plus LH launcher evaluation (post-boronization) 1) boronization recovery 2) LSN staircase RF power in H-mode Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.7e20 /m^2 GPI after initial pair 3) LSN staircase RF power Bt = 5.2 T, Ip = 1 MA, nl04 = 0.7e20 /m^2 GPI 4) LSN staircase RF power Bt = 5.2 T, Ip = 0.6 MA, nl04 = 0.7e20 /m^2 GPI 5) LSN staircase RF power Bt = 5.2 T, Ip = 0.9 MA, nl04 = 0.7e20 /m^2 Neon seeded GPI |
| Entered: Jun 14 2012 05:10:26:367PM |
| Author: Steve Wukitch |
| Boronization recovery was reasonable for all antennas. We completed a
current scan obtaining GPI data along the way. The difference in radiated power in H-mode was neglible between the FA-J and D&E antennas. The impurity source at the FA-J antenna were still lower when the FA-J antenna was operated compared to when D&E were powered. We ran into voltage limits on FA-J often at 1 MA in H-mode. This will be an operational challenge going forward. |
| Physics Operators Plans |
| Entered: Jun 13 2012 02:59:39:287PM |
| Author: Yijun Lin |
| -----------------
Engineering Setup ----------------- Overnight boronization (follow the setup of 1120207) dP: 120 psi TC6:76 mTorr TC9:59 mTorr TC3:3.0mTorr piezo: 40.2 % rmin/rdwell/rmax: 44/75/90cm tdwell/tsweep: 60/120 s EF4 current: 0A pulser; on .7 sec. -off .3 sec. Post boronization ECDC ---------------------------- 1st Gas Setup: Gas: He sweep: 44/103/45 cm scan: 20/120 s Pressure: 5.0e-5 Torr Duration:3 Hrs -------------------------- PO-plan: MP681 Evaluate Field-Aligned Antenna (post-boronization) plus LH launcher evaluation (post-boronization) Run begins at 09:00 and ends at 17:00 Power systems as on: 1120613002 Acoil: +Dtop -Dbot -Jtop +Jbot (standard) Hybrid Enabled Gas setup: Fill B-Top with 6 psi D2 Hybrid enabled (PG4) fill B-side lower with 1 psi Ar Hybrid DISABLED (PG1) leave B-side upper as is Hybrid DISABLED (PG2) fill B-main (C-side) with 40 psi D2 Hybrid enabled (PG3) fill NINJA with 10 psi D2 DISABLED fill H-bottom with 4 psi He4 Hybrid DISABLED (PG5) Enable gate-valves and shutters: ECE, VUV, HiREX Sr, Xeus/LoWEUS Leave z-bolo shutter as is (should be open) Torvac gatevalve toggle (yes/no): no Boronization(yes/no): yes Overnight ECDC (yes/no): yes ICRF(yes/no): yes LH(yes/no): yes Cryopump (yes/no): no DNB (yes/no): yes (for piggy back test for FICX) Vessel temperature: 35/35/35 |
| Session Leader Summaries |
| Entered: Jun 14 2012 03:49:19:653PM |
| Author: Greg Wallace |
| SL summary for 1120614
MP 605 Shots 1-9 The purpose of today's run was to assess the performance of the LH2 antenna following the first boronization. 6 plasmas were allocated to this experiment. The LH power was increased shot to shot, starting at 50 kW/klystron (200 kW net) up to 150 kW/klystron (650 kW net) at 90 deg. No arcing was observed on any shot. A glitch with the PLC prevented the waveguide switches from moving into the launch position just prior to shot 9. |
| Physics Operator Summaries |
| Entered: Jun 14 2012 05:10:14:297PM |
| Author: Yijun Lin |
|
good day. total plasma attempts: 29 fizzles: 4 no power shots (due to ACK failure): 3 Note: PG4 length is now much shorter than yesterday after boronization. I have also lowered IC_EF4U to increase current rise. Note: the TF is started at -1.1 sec, and also programed to 5.2 T in segment 1 (to be the same as in segment 2). This change is to help reduce noise on polarimetry. Note: fizzle detector was moved to 2.3 sec to generate field swing. Note: cooling was slow in the afternoon. After 3 pm, it took ~20 minutesfor between-shot cooling. |
| Session Leader Comments | |||
| Jun 14 2012 09:13:41:410AM | 1120614001 | Greg Wallace | All faults due to poor LH coupling. Density at LH Langmuir probes is near cutoff (2-3e17), although line averaged density is relatively high for LH (nebar ~ 1e20). Seems like boronization must have reduced SOL density. Next shot will reduce outer gap by 4 mm (from 1.1 to .7 cm). |
| Jun 14 2012 09:22:14:407AM | 1120614002 | Jerry Hughes | I am making this entry purely to annoy Matt.
|
| Jun 14 2012 09:23:03:383AM | 1120614002 | Greg Wallace | Clean LH pulse at 50 kW/klystron, 90 deg, just over 200 kW net power. Outer gap didn't change much/any. Density on LH Langmuir probes back up to about 1e18, which resulted in much better coupling and clean pulse.
Increase to 80 kW/klystron for next shot. Decrease nl_04 demand from .7e20 to .5e20, and decrease outer gap by another 4mm. |
| Jun 14 2012 09:29:16:263AM | 1120614003 | Greg Wallace | Fizzle. |
| Jun 14 2012 09:42:36:577AM | 1120614004 | Greg Wallace | Another fizzle. |
| Jun 14 2012 10:02:11:153AM | 1120614005 | Greg Wallace | One early rate fault, then LH ran clean for remainder of the pulse. 350 kW net power at 80 kW/klystron, 90 deg.
Next shot will increase to 120 kW/klystron, try to get density reduced a little, too. 3 plasma shots down, 3 to go. |
| Jun 14 2012 10:18:29:520AM | 1120614006 | Greg Wallace | Clean LH pulse at 120 kW/klystron, 90 deg, 525 kW net power. Some heating on the B row septa.
Next shot will go to 150 kW/klystron. Increase outer gap by 2mm, too. |
| Jun 14 2012 10:30:36:100AM | 1120614007 | Greg Wallace | Clean LH pulse at 150 kW/klystron, 90 deg, 650 kW net power. Next shot will go to 175 kW/klystron. |
| Jun 14 2012 11:20:57:860AM | 1120614009 | Greg Wallace | No LH on this shot. IDC switches did not move back to launch position from load position after the cell access. Pat was able to fix the problem by disabling RF on all klystrons, then actuating switches and re-enabling RF on all klystrons. |
| Jun 14 2012 11:44:27:490AM | 1120614010 | Steve Wukitch | 010 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [0.7, 1.4] sec, 2 MW FA-J: [0.7, 1.4] sec, 1.8 MW Result: plasma - FA-J faulting outgassing is still there but better next: repeat |
| Jun 14 2012 11:44:38:423AM | 1120614011 | Steve Wukitch | 011 fizzle
|
| Jun 14 2012 12:02:49:910PM | 1120614012 | Steve Wukitch | 012 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [0.7, 1.4] sec, 2 MW FA-J: [0.7, 1.4] sec, 1.8 MW Result: plasma - looking better next: move to staircase comparison - similar to 1120613002&3 increase outer gap to 1.5 cm |
| Jun 14 2012 12:19:01:667PM | 1120614013 | Steve Wukitch | 013 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.1,1.5] sec, staircase to 2.2 MW FA-J: [0.6,1] sec, staircase to 2.2 MW Result: plasma - first couple of steps are good from FA-J high power step not so good from FA-J H-mode in second step next: repeat |
| Jun 14 2012 12:37:18:753PM | 1120614014 | Steve Wukitch | 014 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.1,1.5] sec, staircase to 2.2 MW FA-J: [0.6,1] sec, staircase to 2.2 MW Result: plasma - looking better GPI on next: swap antenna order |
| Jun 14 2012 12:45:23:793PM | 1120614015 | Steve Wukitch | 015 ACK failure |
| Jun 14 2012 01:17:23:620PM | 1120614016 | Steve Wukitch | 016 no power |
| Jun 14 2012 01:32:30:730PM | 1120614017 | Steve Wukitch | 017 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [0.6,1] sec, staircase to 2.2 MW FA-J: [1.1,1.6] sec, staircase to 2.2 MW Result: plasma - good first pulse D/E; FA-J faults at high power next: swap antenna order raise upper triangularity to 0.3 from 0.25 |
| Jun 14 2012 02:03:17:047PM | 1120614018 | Steve Wukitch | 018 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.3,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma - upper triangularity is 0.28 FA-J is better next: repeat - need FA-J at high power step |
| Jun 14 2012 02:03:34:813PM | 1120614019 | Steve Wukitch | 019 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.3,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma - upper triangularity is 0.28 FA-J is better next: repeat - need FA-J at high power step |
| Jun 14 2012 02:11:25:910PM | 1120614020 | Steve Wukitch | 020 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.3,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma FA-J is better next: swap antenna order |
| Jun 14 2012 02:38:08:900PM | 1120614021 | Steve Wukitch | 021 request: Bt = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [0.6,1.2] sec, staircase to 2.2 MW FA-J: [1.3,1/5] sec, 2.2 MW Result: plasma good comparison to 020 next: raise Ip to 1 MA |
| Jun 14 2012 02:45:04:930PM | 1120614022 | Steve Wukitch | 022 request: Bt = 5.2 T, Ip = 1 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [0.6,1.2] sec, staircase to 2.2 MW FA-J: [1.3,1.5] sec, 2.2 MW Result: plasma next: swap antenna order |
| Jun 14 2012 02:54:58:953PM | 1120614023 | Steve Wukitch | 023 request: Bt = 5.2 T, Ip = 1 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma next: swap antenna order |
| Jun 14 2012 03:20:16:787PM | 1120614023 | Steve Wukitch | 023 request: Bt = 5.2 T, Ip = 1 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma multiple FA-J faults next: repeat |
| Jun 14 2012 03:43:07:720PM | 1120614024 | Steve Wukitch | 024 request: Bt = 5.2 T, Ip = 1 MA, nl04 = 0.8e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma multiple FA-J faults next: repeat with FA-J lower final step (<2 MW) |
| Jun 14 2012 03:57:40:247PM | 1120614025 | Steve Wukitch | 025 request: Bt = 5.2 T, Ip = 0.6 MA, nl04 = 1e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma multiple FA-J faults next: move on to 0.6 MA |
| Jun 14 2012 04:38:59:320PM | 1120614026 | Steve Wukitch | 026 request: Bt = 5.2 T, Ip = 0.6 MA, nl04 = 0.6e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma - good data next: swap RF antenna order |
| Jun 14 2012 04:39:10:830PM | 1120614027 | Steve Wukitch | 027 request: Bt = 5.2 T, Ip = 0.6 MA, nl04 = 0.6e20 /m^2, LSN
D/E : [1.2,1.5] sec, 2.2 MW FA-J: [0.6,1.2] sec, staircase to 2.2 MW Result: plasma - reasonable RF next: move on to 0.9 MA - no NINJAs or GPI |
| Jun 14 2012 04:58:00:240PM | 1120614028 | Steve Wukitch | 028 request: Bt = 5.2 T, Ip = 0.9 MA, nl04 = 0.8 e20 /m^2, LSN
D/E : [0.7,1.5] sec, 2.2 MW FA-J: [0.7,1.2] sec, 1.8 MW Result: plasma - RF is not so good next: repeat |
| Jun 14 2012 05:10:09:510PM | 1120614029 | Steve Wukitch | 029 fizzle
|
| Physics Operator Comments | |||
| Jun 14 2012 09:08:23:500AM | 1120614001 | Yijun Lin | Shot 1: reload shot 1120613002 (both seg 1 and seg 2)
(No Ar, No Ne). Just try to post-boronization recovery... watch gas pressure carefully... shorten PG4 gas puff...25 ms to 22 ms, anticipating a loaded wall... Load at 14-Jun-2012 08:46:03.00 Open tree /home/ylin/pcs_scratch -1 Open tree done Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.7e20 m^-2 result: full length plasma. first shot after boronization. Start-up not pretty. A bounce. next: increase PG4 from 22 ms to 23 ms. reduce outergap 4 mm. |
| Jun 14 2012 09:22:42:117AM | 1120614002 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.7e20 m^-2
result: Startup good. LH good at 200 kW. ICRF faulty at > 3 MW. Next: lower density to 0.5e20 during LH. reduce outer gap 4 mm more. |
| Jun 14 2012 09:36:32:067AM | 1120614003 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.5e20 m^-2
result: fizzle. Next: no pcs change,and let it run. |
| Jun 14 2012 09:54:24:970AM | 1120614005 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.5e20 m^-2
result: fizzle, 2nd in a row. now I need to do something.. current-rise too slow?? Next: shorten PG4 puff to 22 ms, decrease IC_EF4U by 10 A (-1280 A --> -1290 A) |
| Jun 14 2012 10:08:34:993AM | 1120614005 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.5e20 m^-2
result: plasma full length. outergap 0.5 cm during LH. start-up good. next:lower density more...(but it is just hard to control density right after post-boronization). enable argon. 60 ms. B-side-lower (PG1) |
| Jun 14 2012 10:22:55:263AM | 1120614006 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.4e20 m^-2
result: full-length plasma. density higher than programed (post-boronization wall). LH good. ICRF good. next: disable B-side lower (Argon). increase outer gap by 2 mm. Engineering to change TF start to -1.1 sec (from -1.0 sec). PCS already programed from -1.1 sec. |
| Jun 14 2012 10:41:40:357AM | 1120614007 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.4e20 m^-2
(TF starts @ -1.1 sec) result: plasma full length. density higher than programed. start-up: current rise slow. next: decrease IC_EF4U by 10 A, from -1290A to -1300 A. also rise ZXL by 1 cm...to move the strike point above the slot. |
| Jun 14 2012 11:03:29:680AM | 1120614008 | Yijun Lin | no power shot. Critical failure in INIT.
Josh powercycled the DPCS computer...a lot of complaints from the computer since the beginning of today. |
| Jun 14 2012 11:27:02:333AM | 1120614009 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.4e20 m^-2
result: plasma full-length, but no LH. Startup better. Strike point was higher (for Jim Terry). next: Move to ICRF run...Outer gap to 1.0 cm, density to 0.8e20 m^-2. (also start TF at 5.2 T (current 142500 A) for reduction of noise on Polarimetry |
| Jun 14 2012 11:33:28:363AM | 1120614010 | Yijun Lin | Bt0 = 5.2 T, Ip = 0.8 MA, nl04 = 0.8e20 m^-2
(start TF at 5.2 T (current 142500 A) for reduction of noise on Polarimetry (Irby request) Also moved fizzle detector to 2.3 sec for OH swing... result: full-length plasma. long EDA H-mode. startup good. Next: no dpcs change. |
| Jun 14 2012 11:45:51:160AM | 1120614011 | Yijun Lin | fizzle.
next: shorten PG4 by 1 ms, lower IC_EF4U by 10 A, from -1300 A to -1310 A. |
| Jun 14 2012 12:00:55:050PM | 1120614012 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. Next: increase outer gap by 5 mm. |
| Jun 14 2012 12:16:55:897PM | 1120614013 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. start-up, current rise slow.. Next: shorten PG4 puff by 2 ms. |
| Jun 14 2012 12:34:00:443PM | 1120614014 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. start-up, current rise ok. Next: shorten PG4 puff more by 1 ms to 19 ms. |
| Jun 14 2012 12:43:17:370PM | 1120614015 | Yijun Lin | ACK failure during check...no power shot. |
| Jun 14 2012 12:57:07:733PM | 1120614016 | Yijun Lin | another ACK failure...no power shot. |
| Jun 14 2012 01:35:57:913PM | 1120614017 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. start-up, current rise ok. Next: lower pg3 some more before t=0. increase upper-trangularity slightly (0.20 --> 0.26 by reducing rxu by 1 cm. |
| Jun 14 2012 01:57:02:040PM | 1120614019 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. upper-triangularity 0.28, close to what SL wants. start-up, current rise ok, but Slower than last shot. Next: shorten pg4 by 1 ms (to 18 ms) |
| Jun 14 2012 02:27:27:760PM | 1120614021 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 0.8 MA, nl04 = 0.8e20 m^-2
result: plasma. full length. start-up ok Next:Ip = 1 MA, nl04=1.0e20 m^-2 |
| Jun 14 2012 02:57:27:630PM | 1120614022 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 1 MA, nl04 = 1.0e20 m^-2
result: plasma. full length. start-up ok. current rise slower... Next: reduce pg4 by 1 ms. Problem with CRYO...expecting a short delay before next shot. |
| Jun 14 2012 03:31:59:330PM | 1120614023 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 1 MA, nl04 = 1.0e20 m^-2
result: plasma. full length. start-up ok. current rise slower... Next: reduce pg4 by 1 ms (to 15 ms, this is quite short) Cooling is slow...20 minutes between-shot |
| Jun 14 2012 03:38:24:733PM | 1120614024 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 1 MA, nl04 = 1.0e20 m^-2
result: plasma. full length. start-up ok. current rise slower... Next: no change in dpcs. |
| Jun 14 2012 03:58:39:223PM | 1120614025 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = 1 MA, nl04 = 1.0e20 m^-2
result: plasma. full length. start-up ok. Next: Ip = 0.6 MA, nl04 = 0.6e20 m^-2. |
| Jun 14 2012 04:18:31:913PM | 1120614026 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = .6 MA, nl04 = .6e20 m^-2
result: plasma. full length. start-up ok. Next: no pcs change. |
| Jun 14 2012 04:40:21:433PM | 1120614027 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = .6 MA, nl04 = .6e20 m^-2
result: plasma. full length. start-up ok. Next: ip = 0.9 MA, nl04 = 0.8e20 m^-2. increase pg4 by 2 ms to 17 ms. |
| Jun 14 2012 05:00:43:177PM | 1120614028 | Yijun Lin | Bt0 = 5.2 T (startup 5.2 T), Ip = .9 MA, nl04 = .8e20 m^-2
result: plasma. full length. start-up ok. Next: raise density to 0.95 |
| Jun 14 2012 05:10:05:913PM | 1120614029 | Yijun Lin | fizzle... it is post-5 pm fizzle.
End of run. |
| Engineering Operator Comments | ||||
| Shot | Time | Type | Status | Comment |
| 1 | 08:58:21:197AM | Plasma | Ok | |
| 2 | 09:12:02:417AM | Plasma | Ok | |
| 3 | 09:26:20:613AM | Plasma | Ok | |
| 4 | 09:39:46:527AM | Plasma | Ok | |
| 5 | 09:54:13:107AM | Plasma | Ok | |
| 6 | 10:09:10:307AM | Plasma | Ok | |
| 7 | 10:24:36:207AM | Plasma | Ok | |
| 8 | 10:41:09:263AM | Plasma | Bad | Critical Failure in INIT no power shot. |
| 9 | 11:07:35:470AM | Plasma | Ok | |
| 10 | 11:26:34:603AM | Plasma | Ok | |
| 11 | 11:40:06:563AM | Plasma | Ok | |
| 12 | 11:54:41:540AM | Plasma | Ok | |
| 13 | 12:08:57:777PM | Plasma | Ok | |
| 14 | 12:25:14:310PM | Plasma | Ok | |
| 15 | 12:39:48:790PM | Plasma | Bad | Ack Failure |
| 16 | 12:53:33:647PM | Plasma | Bad | ACK Failure |
| 17 | 01:14:48:150PM | Plasma | Ok | |
| 18 | 01:30:29:950PM | Plasma | Ok | |
| 19 | 01:44:36:253PM | Plasma | Ok | |
| 20 | 02:00:38:983PM | Plasma | Ok | |
| 21 | 02:21:55:417PM | Plasma | Ok | |
| 22 | 02:36:42:040PM | Plasma | Ok | |
| 23 | 03:07:20:220PM | Plasma | Ok | |
| 24 | 03:31:45:527PM | Plasma | Ok | |
| 25 | 03:51:02:520PM | Plasma | Ok | |
| 26 | 04:10:05:063PM | Plasma | Ok | |
| 27 | 04:30:18:253PM | Plasma | Ok | |
| 28 | 04:46:28:887PM | Plasma | Ok | |
| 29 | 05:06:54:750PM | Plasma | Ok | |
| System Availability | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Jun 14 2012 08:58:03:787AM | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Jun 14 2012 11:39:59:120AM | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Jun 14 2012 02:25:43:400PM | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Shoelace Operation:
tOn=1.5 s tOff=2.0 s Freq: Scan between 120 and 170 kHz, six triangle-wave cycle Amp: amp_wave_w at 240 => near full power (~1750 W / 2000 W available). Try to scan in range of QCM as it goes out around 1.5 s. Note that frequency of QCM picks up a little at 1.5 s. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||