| Miniproposals | ||||||||||
| ||||||||||
|
| Operators | |
| Session leader(s): | Yuichi Takase,Yuichi Takase |
| Physics operator(s): | Robert Granetz |
| Engineering operator(s): | Joe Daigle,Frank Silva |
| Engineering Operator Run Comment |
| establish plasma/granetz |
| Session Leader Plans |
| Physics Operators Plans |
| Session Leader Summaries |
| Entered: Jul 7 2004 03:49:15:883PM |
| Author: To Be Determined |
| Run summary 960815 MP159A Re-start machine MP148 RF Cond. (pb) SL: Y. Takase PO: R. Granetz EO: F. Silva/J. Daigle Things to try today: 1. Higher field 6.4T 2. Use steady pre-fill 3. RF assist This was the most successful run of this campaign so far. There were 7 full-length plasma shots: 03, 07, 10, 14, 21, 25, and 27. All of them had breakdown at 6.0T with TF ramping up. Attempts to break down at 5.3T were unsuccessful, so later in the run we made 5.3T plasmas by ramping the TF down after breaking down at 6.0T. They were all at 0.8MA and nel=1.0e20 (later shots had a little lower density, nel=0.9e20). The power radiated into the plasma from the two antennas were in the range 0.1-0.2MW by the end of the run. The run ended early because of an alternator problem. Transmitter #2 has a problem, which needs to be fixed on Monday. Shot 001 Fizzle Higher field (6.0T at t=0) No RF Shot 002 Fizzle tweaked EF4 Shot 003 Plasma!!! reduced pre-fill puff had about 3kW of RF at t=0 Shot 004 Fizzle was supposed to be a repeat. Shot 005 Fizzle another repeat. Shot 006 Fizzle a little lower pre-puff Shot 007 Plasma still a little lower pre-puff Shot 008 Fizzle no change was made Shot 009 Fizzle again no change was made Shot 010 Plasma! no change was made Shot 011 Fizzle Granetz making small wirehead tweaks. Shot 012 Fizzle Granetz making small wirehead tweaks. Shot 013 Disruption @ 0.26s Granetz making small wirehead tweaks. Shot 014 Plasma Granetz making small wirehead tweaks. Shot 015 Fizzle BT=5.3T (was 6.4T) Shot 016 Fizzle no change made Shot 017 Fizzle EF1 tweak (compensate for TF change) Shot 018 Fizzle OH1 tweak Shot 019 Fizzle less pre-fill Shot 020 Fizzle BT=6.0T Shot 021 Plasma 6.4T, like shot 014 (TF still ramping @ breakdown) Shot 022 Fizzle back to 5.3T, but 5.0T @ t=0 (TF still ramping up) Shot 023 Fizzle Turn on TF hybrid control, same startup as 021, and then rampdown to 5.3 T Shot 024 Disrupt @ 0.26s Repeat Shot 025 Plasma Repeat, without RF @ t=0 (starts @ 0.03s) Shot 026 Fizzle Repeat, RF turn on after 0.4s Shot 27 Plasma Repeat, Ip flattop to 1.2s. Shot 28 Fizzle Outer gap programmed to 1cm (was 2cm). Run ended early (3:30) due to an alternator oil leak problem. |
| Physics Operator Summaries |
| Entered: Jul 7 2004 04:36:56:457PM |
| Author: To Be Determined |
| Physics operator's summary for run 960815 MP 159A -- Re-start machine. SL: Y. Takase PO: R. Granetz EO: F. Silva Today's run will again try to get good plasmas after the 5-month shutdown. The initial attempts at this during the past 2 weeks have not yet yielded any more than 0.33 s long discharges, and lots of duds and fizzles. The primary difference today will be operation at higher toroidal field. Summary: The higher toroidal field did the trick. With TF >= 6.0 tesla at breakdown, we had 9 plasmas, 7 of which ramped down successfully. The best was probably 027, which had a flattop to 1.2 s and 200 kW of RF. We could not get current rise with breakdown at 5.3 T, so I got around this problem by using hybrid control of the TF to breakdown at 6.0 T and then ramped back down to 5.4 tesla for the flattop. Obviously this problem needs to be worked on some more. Unlike previous runs, we had no duds today. By the end of the run we were in the familiar alternating pattern between plasmas and fizzles. We made a good start, but there's still a lot to be done to get reliable operation of the machine and the RF. We also still have to run with higher pre-charge and parallel EF4's. See Yuichi's session leader's report for info on the RF. Plasma shots: 003, 007, 010, 013 (disrupted), 014, 021, 024 (disrupted), 025, 027 Scorecard: 9 plasmas (7 full length, 2 disruptions) 19 fizzles (7 with Ip > 50 kA) 0 duds ---------- 28 total Run plan: Establish consistent operation (at any field and any Ip!) Start from yesterday's shot 960814011 (EF4's in series and without high pre-charge), except raise TF field to 6.4 tesla. Another possible thing to try is using a constant pre-fill rather than a pulsed pre-fill. Engineering setup for Thursday 15 Aug 1996: Discharge clean in deuterium overnight. Engineering setup from shot 960814011 (EF4's in series), EXCEPT set the PLC limits on the TF for 6.4 tesla (183 kA on PLC) and start the TF at -1.1 s. gas setup - hybrid enable B-top and A-side fill A-side with 20 PSI of D2 fill B-top with 5 PSI of D2 fill B-side-lower with 4 PSI of Ar Detailed shot log: Shot 01 -- Fizzle. A little too much vertical field. Next shot: 15 amps more negative on EF4 in segment 1. Shot 02 -- Fizzle. Bv was better. Null is fair, but should be good enough. Next shot: reduce pre-pulse gas puff duration from 15 to 13 ms. Shot 03 -- Plasma! Full length rampdown, no disruption. Ip=0.8 MA. OH2's and EFC are working very hard during the first 0.2 s to stabilize plasma position. Prf=0.1 MA, but faulted out at t=0.4 s. NL_04=1.0e20 m-2. Next shot: no changes. Shot 04 -- Fizzle. 55 kA. I think it almost went. No changes for the next shot. Note: on both this and the previous shots, there was 2 kW of RF starting at t=-0.010 s. Shot 05 -- Fizzle, sort of. 100 kA. The GPC shows that the early plasma is moving inwards to the wall. Next shot: reduce pre-pulse gas puff duration from 13 to 12 ms. Note: the OH2U coax resistance is now 2.5 microohms. Shot 06 -- Fizzle, another 100 kA one. GPC still shows the plasma moving inwards. Steve Wolfe also thinks it's moving vertically as well. Next shot: reduce pre-pulse gas puff duration from 12 to 11 ms, in the hopes of getting a faster current rise, to better match the Bz ramp. Note: OH2U coax resistance was slightly less this shot. Shot 07 -- Plasma. Full length, duration=1.5 s, Ip=0.8 MA, no disruption. There's a nasty vertical instability early on, just like on shot 003. OH2U coax resistance came down again. RF crapped out. I'll try one more shot with no changes. Shot 08 -- Fizzle. 60 kA. Just like after the plasma on shot 003. No changes until we get another plasma. Shot 09 -- Fizzle. 80 kA. No changes. Shot 10 -- Plasma. 0.8 MA, 1.5 s, 1.0e20 m-2. RF is still having severe problems. Next shot: tweak up the OH1 voltage around t=0.02 s in order to keep the current rising quickly. Shot 11 -- Fizzle (surprise!) 65 kA. The plasma is still hitting the inboard wall, even with the extra OH1 voltage. For the next shot, try reducing the ramp rate of Bz by lowering the EF3 voltage around t=15 ms. Shot 12 -- Fizzle. 105 kA. Plasma still hits inboard wall. The voltage changes to OH1 and EF3 do not seem to be doing anything. According to Ian and Steve, this may be because the RCUR programming is too dominant. For the next shot, reduce the RCUR offset from 10000 to 7000. Shot 13 -- Plasma, hard disruption at 0.26 s due to vertical instability. The vertical and radial control was much better early on, so those changes in segment 1 were beneficial. The instability after 0.2 s may have been due to kappa > 1.6. CLEARIN was programmed to have a big jump around then, so I've delayed it and ramped it for the next shot. Shot 14 -- Plasma. Good shot. Good stability. Low Prad. Sawtoothing (as have all the previous plasmas today). Prf=0.1 MW. Well, that's two shots in a row, at 6.3 tesla. For the next shot, try lowering the field to 5.3 tesla (PLC setting of 154 kA and at t=-1.0 s). Also enable the argon. Change to 5.3 tesla. Shot 15 -- Fizzle, very weak. No changes for next shot. Shot 16 -- Fizzle, another weak one. On the suggestion of Ian and Steve, I will boost the EF1 currents prior to t=0 by 50 amps (-4800 to -4850) in order to partially offset the drop of 19 kA in the TF single turn at this lower field. Shot 17 -- Fizzle, just like the previous one. For the next shot, add some voltage to OH1 from t=5 to 30 ms. Shot 18 -- Fizzle, no improvement. Next shot: reduce gas and raise early OH1 voltage some more. Shot 19 -- Fizzle, even worse. For the next shot: raise Btor to 6.0 tesla (PLC setting of 174 kA, t=-1.1 s). Also recall shot 014 and re-load. Raise field to 6.0 tesla Shot 20 -- Fizzle. Should have been nearly identical to shot 014. Next shot, raise TF PLC limit back to 183, which should make shot 021 exactly the same as 014. Shot 21 -- Plasma. Good shot. The difference in I_tf at t=0 between this shot and the previous one was only 1-2 kA, but for this shot the TF was not in regulation and for the last shot it was. For the next shot, go back to 5.3 tesla, but start the TF at -0.85 s so that it is not in regulation at t=0. Back down to 5.3 tesla. Shot 22 -- Fizzle, weak. Screw it. Let's go under hybrid TF control and get 5.3 tesla by breaking down at 6.3 and then ramping down. Set PLC at 183 kA, starting at -1.1 s. Turn on hybrid control of TF, start plasma at 6.3 T and then rampdown to 5.3 T. Shot 23 -- Fizzle, weak. Try again, no changes, except move TF change from t=0.10 to t=0.15 s. Shot 24 -- Plasma, but disrupted at t=0.26 s, probably due to a fault in OH2L. Next shot: repeat with no changes, except extend the argon puff by 5 ms, AND TURN OFF THE RF AT T=0. Shot 25 -- Plasma, good shot, even without the RF on at t=0. For the next shot, increase the flattop from 1.0 to 1.2 s (which entails modifying every wire!). Also increase the argon puff by another 5 ms. Shot 26 -- Fizzle, weak. Try again, no changes. Shot 27 -- Plasma, good shot, flattop to 1.2 s. Ip=0.8 MA. Btor=5.45 T during flattop, but 6 tesla and rising at breakdown. For the next shot, reduce the outer gap from 2 cm to 1 cm by increasing RCUR by 5 mm. Note: JR is still not seeing any argon in the plasma. After this shot he went into the cell to make sure the valve wires are okay and the argon bottle valve is open. It checked out okay. So for the next shot, increase pulse width by another 20 ms (total of 50 ms), but reduce the plenum pressure from 4 to 2 psi. Shot 28 -- Fizzle, weak. Try again, no changes. End of run. We had to terminate the run early today because of a problem with an oil leak in the alternator. |
| Session Leader Comments | |||
| Aug 15 1996 08:27:37:530AM | Yuichi Takase | MP159A Re-start machine
MP148 RF Cond. (pb) SL: Y. Takase PO: R. Granetz EO: F. Silva Things to try today: 1. Higher field 6.4T 2. Use steady pre-fill 3. RF assist | |
| Aug 15 1996 08:33:56:490AM | 960815001 | Yuichi Takase | Shot 001 Fizzle
Higher field (6.0T at t=0) No RF |
| Aug 15 1996 08:55:01:450AM | 960815002 | Yuichi Takase | Shot 002 Fizzle
tweaked EF4 |
| Aug 15 1996 09:09:16:960AM | 960815003 | Yuichi Takase | Shot 003 Plasma!!!
reduced pre-fill puff had about 3kW of RF at t=0 |
| Aug 15 1996 09:16:58:030AM | 960815004 | Yuichi Takase | Shot 003 Fizzle
was supposed to be a repeat. |
| Aug 15 1996 09:25:18:000AM | 960815005 | Yuichi Takase | Shot 005 Fizzle
another repeat. |
| Aug 15 1996 09:41:10:560AM | 960815006 | Yuichi Takase | Shot 006 Fizzle
a little lower pre-puff |
| Aug 15 1996 10:14:24:880AM | 960815007 | Yuichi Takase | Shot 007 Plasma
still a little lower pre-puff |
| Aug 15 1996 10:17:22:080AM | 960815008 | Yuichi Takase | Shot 008 Fizzle
no change was made |
| Aug 15 1996 10:38:18:140AM | 960815009 | Yuichi Takase | Shot 009 Fizzle again
no change was made |
| Aug 15 1996 11:02:49:750AM | 960815010 | Yuichi Takase | Shot 010 Plasma!
no change was made |
| Aug 15 1996 11:22:03:460AM | 960815011 | Yuichi Takase | Shot 011 Fizzle
Granetz making small wirehead tweaks. |
| Aug 15 1996 11:23:15:440AM | 960815012 | Yuichi Takase | Shot 012 Fizzle
Granetz making small wirehead tweaks. |
| Aug 15 1996 11:38:32:570AM | 960815013 | Yuichi Takase | Shot 013 Disruption @ 0.26s
Granetz making small wirehead tweaks. |
| Aug 15 1996 11:54:59:950AM | 960815014 | Yuichi Takase | Shot 014 Plasma
Granetz making small wirehead tweaks. |
| Aug 15 1996 12:06:51:640PM | 960815015 | Yuichi Takase | Shot 015 Fizzle
BT=5.3T (was 6.4T) |
| Aug 15 1996 12:26:25:890PM | 960815016 | Yuichi Takase | Shot 016 Fizzle
no change made |
| Aug 15 1996 12:48:37:570PM | 960815017 | Yuichi Takase | Shot 017 Fizzle
EF1 tweak (compensate for TF change) |
| Aug 15 1996 12:49:16:440PM | 960815018 | Yuichi Takase | Shot 018 Fizzle
OH1 tweak |
| Aug 15 1996 01:06:33:330PM | 960815019 | Yuichi Takase | Shot 019 Fizzle
less pre-fill |
| Aug 15 1996 01:16:15:770PM | 960815020 | Yuichi Takase | Shot 020 Fizzle
BT=6.0T |
| Aug 15 1996 01:40:08:170PM | 960815021 | Yuichi Takase | Shot 021 Plasma
6.4T, like shot 014 (TF still ramping @ breakdown) |
| Aug 15 1996 01:53:56:410PM | 960815022 | Yuichi Takase | Shot 022 Fizzle
back to 5.3T, but 5.0T @ t=0 (TF still ramping up) |
| Aug 15 1996 02:17:55:570PM | 960815023 | Yuichi Takase | Shot 023 Fizzle
Turn on TF hybrid control, same startup as 021, and then rampdown to 5.3 T |
| Aug 15 1996 02:33:25:370PM | 960815024 | Yuichi Takase | Shot 024 Disrupt @ 0.26s
Repeat |
| Aug 15 1996 02:35:25:260PM | 960815025 | Yuichi Takase | Shot 025 Plasma
Repeat, without RF @ t=0 |
| Aug 15 1996 02:52:31:990PM | 960815026 | Yuichi Takase | Shot 026 Fizzle
Repeat, RF turn on after 0.4s |
| Aug 15 1996 03:24:21:370PM | 960815027 | Yuichi Takase | Shot 27 Plasma
Repeat with no changes. |
| Physics Operator Comments | |||
| Aug 14 1996 06:00:15:780PM | Robert Granetz | Run plan:
Establish consistent operation (at any field and any Ip!) Start from yesterday's shot 960814011 (EF4's in series and without high pre-charge), except raise TF field to 6.4 tesla. Another possible thing to try is using a constant pre-fill rather than a pulsed pre-fill. | |
| Aug 14 1996 06:00:29:410PM | Robert Granetz | Engineering setup for Thursday 15 Aug 1996:
Discharge clean in deuterium overnight. Engineering setup from shot 960814011 (EF4's in series), EXCEPT set the PLC limits on the TF for 6.4 tesla (183 kA on PLC) and start the TF at -1.1 s. gas setup - hybrid enable B-top and A-side fill A-side with 20 PSI of D2 fill B-top with 5 PSI of D2 fill B-side-lower with 4 PSI of Ar | |
| Aug 15 1996 08:25:17:700AM | Robert Granetz | MP 159A -- Re-start machine.
SL: Y. Takase PO: R. Granetz EO: F. Silva Today's run will again try to get good plasmas after the 5-month shutdown. The initial attempts at this during the past 2 weeks have not yet yielded any more than 0.33 s long discharges, and lots of duds and fizzles. The primary difference today will be operation at higher toroidal field. | |
| Aug 15 1996 08:37:36:690AM | 960815001 | Robert Granetz | Shot 01 -- Fizzle. A little too much vertical field. Next shot: 15 amps more
negative on EF4 in segment 1. |
| Aug 15 1996 08:49:31:970AM | 960815002 | Robert Granetz | Shot 02 -- Fizzle. Bv was better. Null is fair, but should be good enough.
Next shot: reduce pre-pulse gas puff duration from 15 to 13 ms. |
| Aug 15 1996 09:05:23:710AM | 960815003 | Robert Granetz | Shot 03 -- Plasma! Full length rampdown, no disruption. Ip=0.8 MA. OH2's
and EFC are working very hard during the first 0.2 s to stabilize plasma position. Prf=0.1 MA, but faulted out at t=0.4 s. NL_04=1.0e20 m-2. Next shot: no changes. |
| Aug 15 1996 09:13:51:100AM | 960815004 | Robert Granetz | Shot 04 -- Fizzle. 55 kA. I think it almost went. No changes for the next
shot. Note: on both this and the previous shots, there was 2 kW of RF starting at t=-0.010 s. |
| Aug 15 1996 09:50:46:840AM | 960815006 | Robert Granetz | Shot 06 -- Fizzle, another 100 kA one. GPC still shows the plasma moving
inwards. Steve Wolfe also thinks it's moving vertically as well. Next shot: reduce pre-pulse gas puff duration from 12 to 11 ms, in the hopes of getting a faster current rise, to better match the Bz ramp. Note: OH2U coax resistance was slightly less this shot. |
| Aug 15 1996 10:02:13:730AM | 960815007 | Robert Granetz | Shot 07 -- Plasma. Full length, duration=1.5 s, Ip=0.8 MA, no disruption.
There's a nasty vertical instability early on, just like on shot 003. OH2U coax resistance came down again. RF crapped out. I'll try one more shot with no changes. |
| Aug 15 1996 10:19:16:400AM | 960815008 | Robert Granetz | Shot 08 -- Fizzle. 60 kA. Just like after the plasma on shot 003. No changes
until we get another plasma. |
| Aug 15 1996 10:42:55:760AM | 960815009 | Robert Granetz | Shot 09 -- Fizzle. 80 kA. No changes.
|
| Aug 15 1996 10:53:22:000AM | 960815010 | Robert Granetz | Shot 10 -- Plasma. 0.8 MA, 1.5 s, 1.0e20 m-2. RF is still having severe
problems. Next shot: tweak up the OH1 voltage around t=0.02 s in order to keep the current rising quickly. |
| Aug 15 1996 11:15:12:650AM | 960815011 | Robert Granetz | Shot 11 -- Fizzle (surprise!) 65 kA. The plasma is still hitting the
inboard wall, even with the extra OH1 voltage. For the next shot, try reducing the ramp rate of Bz by lowering the EF3 voltage around t=15 ms. |
| Aug 15 1996 11:26:39:630AM | 960815012 | Robert Granetz | Shot 12 -- Fizzle. 105 kA. Plasma still hits inboard wall. The voltage
changes to OH1 and EF3 do not seem to be doing anything. According to Ian and Steve, this may be because the RCUR programming is too dominant. For the next shot, reduce the RCUR offset from 10000 to 7000. |
| Aug 15 1996 11:43:14:840AM | 960815013 | Robert Granetz | Shot 13 -- Plasma, hard disruption at 0.26 s due to vertical instability.
The vertical and radial control was much better early on, so those changes in segment 1 were beneficial. The instability after 0.2 s may have been due to kappa > 1.6. CLEARIN was programmed to have a big jump around then, so I've delayed it and ramped it for the next shot. |
| Aug 15 1996 11:57:02:760AM | 960815014 | Robert Granetz | Shot 14 -- Plasma. Good shot. Good stability. Low Prad. Sawtoothing (as
have all the previous plasmas today). Prf=0.1 MW. Well, that's two shots in a row, at 6.3 tesla. For the next shot, try lowering the field to 5.3 tesla (PLC setting of 154 kA and at t=-1.0 s). Also enable the argon. |
| Aug 15 1996 12:10:13:710PM | 960815015 | Robert Granetz | Change to 5.3 tesla.
Shot 15 -- Fizzle, very weak. No changes for next shot. |
| Aug 15 1996 12:25:20:900PM | 960815016 | Robert Granetz | Shot 16 -- Fizzle, another weak one. On the suggestion of Ian and Steve, I
will boost the EF1 currents prior to t=0 by 50 amps (-4800 to -4850) in order to partially offset the drop of 19 kA in the TF single turn at this lower field. |
| Aug 15 1996 12:51:23:880PM | 960815018 | Robert Granetz | Shot 18 -- Fizzle, no improvement. Next shot: reduce gas and raise early OH1
voltage some more. |
| Aug 15 1996 01:07:00:730PM | 960815019 | Robert Granetz | Shot 19 -- Fizzle, even worse. For the next shot: raise Btor to 6.0 tesla
(PLC setting of 174 kA, t=-1.1 s). Also recall shot 014 and re-load. Raise field to 6.0 tesla |
| Aug 15 1996 01:20:18:360PM | 960815020 | Robert Granetz | Shot 20 -- Fizzle. Should have been nearly identical to shot 014. Next shot,
raise TF PLC limit back to 183, which should make shot 021 exactly the same as 014. |
| Aug 15 1996 01:43:27:620PM | 960815021 | Robert Granetz | Shot 21 -- Plasma. Good shot. The difference in I_tf at t=0 between this
shot and the previous one was only 1-2 kA, but for this shot the TF was not in regulation and for the last shot it was. For the next shot, go back to 5.3 tesla, but start the TF at -0.85 s so that it is not in regulation at t=0. |
| Aug 15 1996 01:49:15:140PM | 960815022 | Robert Granetz | Back down to 5.3 tesla.
Shot 22 -- Fizzle, weak. Screw it. Let's go under hybrid TF control and get 5.3 tesla by breaking down at 6.3 and then ramping down. |
| Aug 15 1996 02:28:56:440PM | 960815023 | Robert Granetz | Shot 23 -- Fizzle, weak. Try again, no changes, except move TF change from
t=0.10 to t=0.15 s. |
| Aug 15 1996 02:25:42:980PM | 960815024 | Robert Granetz | Shot 24 -- Plasma, but disrupted at t=0.26 s, probably due to a fault in OH2L.
Next shot: repeat with no changes, except extend the argon puff by 5 ms, AND TURN OFF THE RF AT T=0. |
| Aug 15 1996 02:44:26:270PM | 960815025 | Robert Granetz | Shot 25 -- Plasma, good shot, even without the RF on at t=0. For the next
shot, increase the flattop from 1.0 to 1.2 s (which entails modifying every wire!). Also increase the argon puff by another 5 ms. |
| Aug 15 1996 02:49:05:240PM | 960815026 | Robert Granetz | Shot 26 -- Fizzle, weak. Try again, no changes.
|
| Aug 15 1996 03:18:37:500PM | 960815027 | Robert Granetz | Shot 27 -- Plasma, good shot, flattop to 1.2 s. Ip=0.8 MA. Btor=5.45 T during
flattop, but 6 tesla and rising at breakdown. For the next shot, reduce the outer gap from 2 cm to 1 cm by increasing RCUR by 5 mm. Note: JR is still not seeing any argon in the plasma. After this shot he went into the cell to make sure the valve wires are okay and the argon bottle valve is open. It checked out okay. So for the next shot, increase pulse width by another 20 ms (total of 50 ms), but reduce the plenum pressure from 4 to 2 psi. |
| Aug 15 1996 03:22:12:180PM | 960815028 | Robert Granetz | Shot 28 -- Fizzle, weak. Try again, no changes.
|
| Aug 15 1996 03:45:07:350PM | 960815028 | Robert Granetz | End of run. We had to terminate the run early today because of a problem with
an oil leak in the alternator. |
| Engineering Operator Comments | ||||
| Shot | Time | Type | Status | Comment |
| 1 | 08:28:16:530AM | Plasma | Ok | oh2 bypass comm fault |
| 2 | 08:42:52:620AM | Plasma | Ok | no faults |
| 3 | 08:53:25:390AM | Plasma | Ok | no faults, firs sustained plasma |
| 4 | 09:08:55:600AM | Plasma | Ok | no faults |
| 5 | 09:23:43:320AM | Plasma | Ok | |
| 6 | 09:38:30:270AM | Plasma | Ok | no faults |
| 7 | 09:53:00:570AM | Plasma | Ok | no faults |
| 8 | 10:14:14:990AM | Plasma | Ok | oh2u comm fault bypass cab |
| 9 | 10:28:54:520AM | Plasma | Ok | oh2u comm fault bypass cab |
| 10 | 10:43:50:060AM | Plasma | Ok | no faults |
| 11 | 11:01:39:410AM | Plasma | Ok | no faults |
| 12 | 11:16:05:010AM | Plasma | Ok | no faults |
| 13 | 11:30:46:740AM | Plasma | Ok | no faults |
| 14 | 11:45:34:520AM | Plasma | Ok | no faults |
| 15 | 12:02:05:950PM | Plasma | Ok | no faulta |
| 16 | 12:16:52:300PM | Plasma | Ok | no faults |
| 17 | 12:30:50:180PM | Plasma | Ok | no faults |
| 18 | 12:42:58:520PM | Plasma | Ok | no faults |
| 19 | 12:55:48:540PM | Plasma | Ok | no faults |
| 20 | 01:10:06:230PM | Plasma | Ok | no faults |
| 21 | 01:22:45:460PM | Plasma | Ok | no faults |
| 22 | 01:42:13:700PM | Plasma | Ok | no faults |
| 23 | 02:01:54:140PM | Plasma | Ok | no faults tf in hybrid control |
| 24 | 02:14:07:150PM | Plasma | Ok | no faults |
| 25 | 02:27:38:390PM | Plasma | Ok | |
| 26 | 02:46:07:620PM | Plasma | Ok | |
| 27 | 02:58:43:920PM | Plasma | Ok | |
| 28 | 03:19:26:180PM | Plasma | Ok | NO faults |